background image

3.6 Signal 

RS422 Cable Requirements 

This cable is a 6-conductor shielded cable used to transmit an RS/422 signal. This shielded cable 
consists of unpaired wires. They should not be subjected to mechanical flexing after installation. 
This cable is not for direct burial and should have one of the following routings: 
 

· 

In dedicated metallic conduit 

· 

Inside buildings 

-

 if cable is not in conduit, keep away from interference signals.  

 
With interference signals (such as power conductors, intercom, etc.) typically a two-foot 
separation is required. The maximum length of an RS/422 signal cable is 4,000 feet (1.22 
kilometers). 

Signal Connect on from Compu er to Sign 

i

t

One end of the signal cable should be terminated to the 6-position terminal block in the sign 
labeled “RS422 IN” (TB2). The opposite end is terminated at the signal converter (Daktronics part 
number 0A-1127-0237) in the control room. 
 

 

Signal Converter (J4/J5) 

 

Field Cabling 

Terminal Block TB2 

(RS422 In) 

Pin 1 (GND) 

Red 

Pin 1 (GND) 

Pin 2 (RX-P) 

Black 

Pin 2 (TX-P) 

Pin 3 (RX-N) 

Brown 

Pin 3 (TX-N) 

Pin 4 (TX-P) 

White 

Pin 4 (RX-P) 

Pin 5 (TX-N) 

Blue 

Pin 5 (RX-N) 

Pin 6 (GND) 

Green 

Pin 6 (GND) 

Signal Termination Between Two (o  More) Signs 

r

This is the most common method of terminating signal between two or more signs. A 6-conductor 
cable is used and one end terminates at the “RS422 OUT” 6-position terminal block (TB3) on the 
first sign. The other end terminates at the “RS422 IN” 6-position terminal block (TB2) in the 
second sign.

 

 

Sign A 

Data Out (TB3) 

 

Field Cabling 

Sign B 

Data In (TB2) 

Pin 1 (GND) 

Green 

Pin 6 (GND) 

Pin 2 (Data TX-N) 

Blue 

Pin 5 (Data RX-N) 

Pin 3 (Data TX-P) 

White 

Pin 4 (Data RX-P) 

Pin 4 (Data RX-N) 

Brown 

Pin 3 (Data TX-N) 

Pin 5 (Data RX-P) 

Black 

Pin 2 (Data TX-P) 

Pin 6 (GND) 

Red 

Pin 1 (GND) 

Pin 6(GND) 

Bare (Shield) 

N.C. 

 
Note: Refer to 

Section 4.2

 for the modem information. This is found on pages 

4-1 

and 

4-2

3.7  First Time Operation 

When first operated, the sign will run through an initialization in which it will display the following: 
 

1. Output 

Test 

(DDDs) 

2.  Product Name (Galaxy) 

3.  Sign Size (Row x Column) 
4.  Firmware Number (

ED10134

Electrical Installation 

3-5

 

 

Содержание Galaxy AF-3050 Series
























































































Отзывы: