background image

FLR3-100 Installation Quick Guide

13 June 2017
DD2291475
Rev 06

201 Daktronics Drive Brookings, SD 57006

www.daktronics.com/support

800.325.8766

Page 1 of 4

This quick guide provides steps for installing the receiver and setting up a FLR3-100 key fob with a 

Fuelight

TM

 Gen 3 display.

Installing the Receiver

1. 

Using a flat-head screwdriver, open the digit face to access inside 

the digit cabinet.

2.  Remove both antenna hole plugs from the digit face. Refer to 

Figure 1

3.  Place the receiver on to the mounting studs on the back of the 

digit face. Refer to 

Figure 2

.

4.  Use a 

5

/

16

" nut driver to secure the receiver to the mounting studs 

using the two provided nuts. 

5.  Place the threaded end of the antenna cable through the 

antenna hole. 

6. 

Place the flat washer over the threaded end of the antenna cable. Refer 

to 

Figure 2

.

7.  Thread the provided nut on to the threaded end of the antenna cable 

and tighten using an 

11

/

32

" wrench. 

8.  Thread the female end of the antenna on to the threaded end of the 

antenna cable and turn the antenna clockwise until snug. Refer to 

Figure 2

.

9.  Connect the receiver cable from receiver to the driver. Refer to 

Figure 3

.

10.  Neatly secure any excess cable with cable ties. 
11.  Close and secure the digit face.

Setting the Security DIP Switches

The FLR3-100 key fob has a series of dip switches on the back to give it a unique address setting. Set 

these switches to a unique setting to prevent others from being able to control your display.
1.  Remove the small cover on the back of the FLR3-100 key fob radio. Refer to 

Figure 4

.

2. 

Using a paper clip or a micro screwdriver, set the switches to a unique setting. 

3.  Replace the back cover.

Antenna Hole Plug

AH

Mounting Stud

Figure 1: 

Digit Door Receiver 

Mounting Overview

Receiver

Antenna

Mounting Stud

Nut

Digit Face

Nut

Washer

Figure 2: 

Mounting Profile

Figure 3: 

Final Receiver Assembly

Digit Cabinet

Driver

Receiver

Antenna Cable

Note: 

Do not change switches nine and zero.

Содержание FLR3-100

Страница 1: ...of the antenna cable and tighten using an 11 32 wrench 8 Thread the female end of the antenna on to the threaded end of the antenna cable and turn the antenna clockwise until snug Refer to Figure 2 9 Connect the receiver cable from receiver to the driver Refer to Figure 3 10 Neatly secure any excess cable with cable ties 11 Close and secure the digit face Setting the Security DIP Switches The FLR3...

Страница 2: ...he decimal begins to flash This takes about five seconds 3 While the display slowly flashes press the 2 button until the appropriate line number is shown on the display L01 L02 etc 4 Once the line number is set press and hold the 2 and 2 buttons until the next display face begins to slowly flash 5 Repeat these steps until all display faces have been correctly mapped 6 Exit configuration mode by pr...

Страница 3: ...nd holding the 4 and 4 buttons until the displays return to showing prices approximately five seconds Controlling Five or More Fuel Grades or Multiple Pylons Use the following steps when controlling more than four fuel grades in the same pylon or when more than one pylon exists on the same site Important Terms Host Display Display that has the receiver card connected to it Fuelight System Host dis...

Страница 4: ...ed to all pylons and Fuelight systems All Fuelight systems turn off and on simultaneously requiring access to the inside of the host display of each Fuelight system to sync to its dedicated key fob 1 In the host display of each Fuelight system unplug the driver power supply 2 Power up the first Fuelight system by reconnecting the power supply to the driver 3 Sync the keyfob per Section Mating the ...

Отзывы: