Dakota Digital MCL-36K-SPD, Руководство по установке

Страница: 5 / 6

5
MAN#650333:B
PerF PerF PerF PerF Performance Menu setup
The performance readings can be turned on or off. When they are turned off the odometer will only toggle through the
mileage readings.
•
Press and release the switch until “ PErF ” is displayed, then press and hold the switch until “ - ” is displayed.
•
Release the switch. The current setting will be displayed (“ on ” or “ oFF ”).
•
Press and release the switch until the desired setting is displayed.
•
Press and hold the switch until “ - ” is displayed to save the setting.
F
FF Fv vv vEL EL EL EL Fuel sender selection DEFAULT OFF
This setting should be set to “ oFF ”, this may be used for future accessories. The options are to allow the fuel information to be
introduced to the data bus. This menu is not really important but is here in case future accessories require it. You should not
harm anything if the settings are incorrect, but OFF is the default setting at this point.
•
Press and release the switch until “ FvEL ” is displayed, then press and hold the switch until “ - ” is displayed.
•
Release the switch. The current setting will be displayed (“ oFF ” or “ on ”).
•
Press and release the switch until the desired setting is displayed.
•
Press and hold the switch until “ - ” is displayed to save the setting.
•
If “ on ” is selected, then “ done ”, “ test ”, “ reset ”, or “ adjust ” options will be displayed. “ TEST ” shows the current fuel reading.
“ RESET ” and “ ADJUST ” change the fuel data sent on the bus and will not normally need to be changed.
•
Press and release the switch until “ done ” is displayed. Press and hold the switch until “ - ” is displayed to exit.
RANGE
RANGE RANGE
RANGE Distance to Empty setup
The range reading will initially show the word “ range ” until a tank of gas has been driven to allow the gauge to complete its
setup based on your driving. Begin with a full tank of gas and do not refill it until it gets below ¼ tank of gas. This can be done on
multiple trips as long as no fuel is added before it gets low enough. After the initial setup the display will show “
r ” followed by the
calculated distance to empty. This will count down, making adjustments as necessary, until the range is 35 miles (56km) or less and
then it will show “
r Lo ”. The gauge will continue to make adjustments to match your driving habits with each fill up. After the initial
setup you are not required to wait for the fuel to get below ¼ tank before refilling.
•
Press and release the switch until “ RANGE ” is displayed, then press and hold the switch until “ - ” is displayed.
•
The display will show “ oFF ” or “ oN ”. Press and release the switch to change to the desired setting.
•
Press and hold the switch until “ - ” is displayed to select the setting.
•
“ OFF ” turns the range display off.
•
Turning the function
on
will access the following menus
o donE (exits the setup)
o rESEt (resets the gauge to beginning of the initial range learning)
o sender (used to change or reset the fuel gauge readings)
d10 (set to 2004 – 2007 model with Dakota Digital fuel gauge)
d33 (set to 2008 – 2012 model with Dakota Digital fuel gauge)
H04 (set to 2004 – 2007 factory fuel gauge)
H08 (set to 2008 – 2012 factory fuel gauge)
d-C (set to a custom fuel curve with Dakota Digital fuel gauge)
•
SET 00 (set new empty reading, “ done ” indicates it was stored, “ error ” indicates the
signal is out of range)
•
SET 99 (set new full reading)
CSt (set to a custom fuel curve with factory fuel gauge)
•
SET 00 (set new empty reading, “ done ” indicates it was stored, “ error ” indicates the
signal is out of range)
•
SET 99 (set new full reading)
•
Press and release the switch to select the desired fuel setup menu, press and hold it until “ - ” is displayed, and then release the
switch to view or go on.
•
A press and hold will save the setting or exit back to the menu.
•
“ done ” is the first menu displayed, a press and hold will exit fuel set up at this point.
•
“ rESEt ” will begin the initial range learning again. You must begin with a full tank of gas and then ride it down to less than ¼ tank.
This can be done in multiple trips as long as the tank is not filled in between. The range display will show “ range ” until this is
completed and then begin showing the distance to empty.
•
“ SENDER ” is used to select the type of fuel sender and gauge being used to allow the speedometer to read the fuel level accurately.