background image

11

LEGAL NOTICES

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this 

device may not cause harmful interference, and (2) this device must accept any interference received, including 

interference that may cause undesired operation. Changes or modifications not expressly approved by the party 

responsible for compliance could void the user’s authority to operate the equipment. This equipment has been 

tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These 

limits are designed to provide reasonable protection against harmful interference in a residential installation. This 

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance 

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that 

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try 

to correct the interference by one or more of the following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

 

WARNING: 

Cancer and Reproductive Harm. Go t

www.P65Warnings.ca.gov

 for more information.

Содержание DCMT-4000













Отзывы: