background image

Mount the transmitter with the LED 
towards the top for proper installation.

LOW BATTERY ALERT:

 If the receiver 

sounds a second alert 30 seconds after the 
first alert, provided nothing activates the 
transmitter again, the 9-volt battery in the 
transmitter should be changed.

Correct 

Installation

Incorrect 

Installation

LED

LED

CODING THE TRANSMITTER:

 

Note: The transmitters and receivers are preset at the factory. DO NOT 
change settings, unless changing the tune or experiencing false signals.

1.   Locate the dip switches in the DCMT-2500 circuit board (Figure 5).
2.   The first eight dip switches are for the frequency setting (256 

combinations). Set switches 1-8 (Figure 5-3) to match the eight 
switches in the receiver.

3.   Switches 9 and 10 (Figure 5-4) are for the zone/channel settings on 

the transmitter. The four zones are listed in the table below.

LOW BATTERY ALERT:

 If the receiver sounds a second

 

alert 30 seconds after the first alert, provided nothing 
activates the transmitter again, the 9-volt battery in the 
transmitter should be changed.

CODING THE RECEIVER:

1.   Open the receiver case by inserting a small 

screwdriver into one of the pry notches on the side 
of the case. (refer to receiver manual)

2.   Gently lift off the front cover.
3.   Locate the eight dip switches on the receiver and make sure they are set identically to dip switches 1-8 

on the transmitter.

Note: If more than one transmitter is used with the receiver, the first eight dip switches of all 
transmitters must match the eight dip switches of the receiver.

Note: Whenever a change is made to the time jumper or the dip switches, the receiver must be 
turned OFF and then back ON to operate properly.

Switch 9 Switch 10

Channel

Tune

On

On

1

Classical

Off

On

2

Westminster

On

Off

3

Ding Dong

Off

Off

4

Whistle

PIR SETTINGS: 

(FIGURE 4)

   

The jumpers settings are as follows:

Range:

   High: more than 15 metres

 

Medium: 6-15 metres

 

Low: less than 6 metres

LED:

  

ON: LED will flash when it detects

 

OFF: LED is always dark

Filter:

   ON: set for outdoor use

 

OFF: set for indoor use

Reset: 

  10 seconds to reset after activation

 

120 seconds to reset after activation

Note: If the range is set to “low,” the filter should be set to 
“off” or the detection will be limited.

FIGURE 4

PIR with cover 

removed

Reset

Filter

LED

Range

FIGURE 5

3

4

Содержание DCMT-2500

Страница 1: ...EALAND AUSTRALIA WARNING This device complies with Part 15 of the FCC rules operation of this device is subject to the following conditions 1 This device may not cause harmful interference 2 This device must accept any interference including interference that may cause undesired operation ...

Страница 2: ...metal siding and stucco can reduce the range MOUNTING THE TRANSMITTER 1 Select a location to mount the transmitter such as a post or tree 2 For best results the transmitter should be about 500mm off the ground and about 6 metres from the side of the drive 3 The transmitter will detect people or vehicles to about 15 metres but occasionally it may detect much farther For this reason it is best to av...

Страница 3: ...hanged CODING THE RECEIVER 1 Open the receiver case by inserting a small screwdriver into one of the pry notches on the side of the case refer to receiver manual 2 Gently lift off the front cover 3 Locate the eight dip switches on the receiver and make sure they are set identically to dip switches 1 8 on the transmitter Note If more than one transmitter is used with the receiver the first eight di...

Страница 4: ...veway Move the transmitter closer to the receiver Keep the transmitter away from large metal objects that may interfere with the radio signal TECHNICAL SUPPORT If you encounter any difficulty in the operation of this product after reading the manual please contact us We will be happy to answer your questions and help you in any way we can WARRANTY Dakota Alert warrants this product to be free of d...

Отзывы: