background image

This device complies with Part 15 of the FCC Rules.  Operation is subject to the following two conditions: (1) this 

device may not cause harmful interference, and (2) the device must accept any interference received, including 

interference that may cause undesired operation.  Changes or modifications not expressly approved by the part 

responsible for compliance could void the users authority to operate the equipment.  This equipment has been 

tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  

These limits are designed to provide reasonable protection against harmful interference in a residential instal-

lation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful interference to radio communications.  However, there is 

no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful 

interference to radio or television reception, which can be determined by turning the equipment off and on, 

the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

           

           WARNING

: Cancer and Reproductive Harm.  Go to www.P65Warnings.ca.gov for more information

LEGAL NOTICES

11

Содержание DAPT-4000













Отзывы: