Dakota Alert AD-01 Kit Скачать руководство пользователя страница 11

Страница: 11 / 16

How to stop the Dialer from dialing the telephone numbers in sequence:

When the Auto Dialer starts dialing, it will dial the first telephone number and repeat the

pre-recorded voice message for 1 minute. If there is no response from the phone, then it

will hang up and dial the next number until all the programmed numbers for that alarm are

dialed. It will repeat this dial sequence three times and display

‘NO ANSWER’

if there is no

response from any of the phone numbers. To stop this dial sequence, press the

key on the

telephone keypad that is receiving the call. At that time, the Auto Dialer will stop its dialing

sequence and the alarm (if programmed) will stop. If the local alarm has been programmed

as active, then pressing the

key will stop the dialing sequence, but the alarm will continue

to sound until timed out. In both cases, the Auto Dialer will remain ON, waiting for any

further alarm.

Quick guide: Answer the phone and press

to stop dialing sequence.

How to put the system into PANIC AlARM:

Press both the

and the

OFF

buttons on the RF Keyfob at the same time, for 3 seconds.

The dialer will now dial out

(Alarm 2)

whether the system is armed or disarmed.

AD-01 Kit Manual.indd 11

10/15/2009 10:17:55 AM

Содержание AD-01 Kit

















Результаты поиска

Содержание AD-01 Kit

Отзывы:

Похожие инструкции для AD-01 Kit

Бренды по названию

Популярные бренды

Dakota Alert AD-01 Kit, Руководство пользователя

Результаты поиска

Содержание AD-01 Kit

Отзывы:

Похожие инструкции для AD-01 Kit

Бренды по названию

Популярные бренды