background image

Model 9016 X-Purge Operator Interface 

 

Daisy Data Displays, Inc. 

February 2022 

D010-000002 

Limited Warranty and Liability Statement 

To the original purchaser, Daisy Data Displays, Inc., hereinafter referred to collectively as SELLER, 

warrants each of its manufactured products, and all components therein contained to be free 

from defects in materials and/or workmanship 

for a period of 24  months

  from the date of 

purchase. 
Should a malfunction or other indication of defect attributable directly to faulty materials and/or 

workmanship occur, Seller will, at its option, and without charge to the customer for labor and 

parts, repair or replace  the defective product, F.O.B. Seller’s plant, but Seller will not be 

responsible for freight from Purchaser to Seller’s plant. 
In no event shall Seller be liable for any loss, inconvenience, or damage, whether direct, incidental, 

consequential or otherwise resulting from abuse, misapplication, or modification of the product, 

improper or faulty power, damage resulting from repairs or alterations performed by 

unauthorized persons, or conditions resulting from any other equipment attached to the product. 

Seller assumes no liability for damage occurring in transit due to the product not being returned 

in its original shipping material. 

This warranty is exclusive and is in lieu of any warranty of merchantability or fitness for a 

particular purpose or other warranty of quality whether expressed or implied, except of title 

and against patent infringement

.  Correction of nonconformities, in the manner and for the 

period of time provided above, shall constitute fulfillment of all liabilities of the Seller to the 

Purchaser with respect to, or arising out of the goods, whether based on contract, negligence, 

strict tort or otherwise. 
 

LIMITATION OF LIABILITY:

 The Seller shall not under any circumstances be liable for special or 

consequential damages, such as, but not limited to, damage or loss of other property or 

equipment, loss of profits or revenues, cost of capital, cost of purchased or replacement goods, 

or claims of customers of Purchaser for service interruptions.  The remedies of the Purchaser set 

forth herein are exclusive, and the liability of Seller respect to any contract, or anything done in 

connection therewith such as the performance or breach thereof, of from the manufacture, sale, 

delivery, resale, installation or use of any goods covered by or furnished under this contract 

whether arising out of contract, negligence, strict tort or breach of warranty or otherwise, shall 

not, except as expressly provided herein, exceed the price of the goods upon which such liability 

is based. 
 

This warranty gives you specific legal rights, and you may also have other rights, which vary from 

state to state. Seller makes every effort to provide clear and accurate technical information on the 

application of its products in the Operator's Manual and assumes no liability for misuse of the 

information. 

Содержание 9016 X-Purge








































Отзывы: