Installation Guide
Daintree
®
Networked General Purpose Adapter (WGA100)
The Installation Test procedure fails.
1.
Confirm that the WGA100 is powered.
2.
Check the connections from the WGA100 to the devices.
3.
Check to be sure the WGA100 DIP switch settings are correct.
4.
Press and hold the Reset button for 3 seconds to reset
the WGA100.
5.
Perform the Installation Test again.
11
12
Troubleshooting
Class A Digital Device (CE)
13
14
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and radiates radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encourage to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna;
• Increase the separation between the equipment
and receiver;
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected;
• Consult the dealer or an experienced radio/TV technician
for help.
Product complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation. CAN ICES-005 B / NMB-005 B
FCC Warning Message
Industry Canada (IC) Warning Message
Input Voltage
120-277VAC, 50-60Hz
Switched Output
15A @ 120-277 VAC
Relay
1 hp @ 120-230 VAC
Low Voltage
24VDC; 75mA maximum
Output
Analog Output
0-10VDC, 5mA max
Analog Input
0-10VDC
Binary Inputs (2)
Active high.
Binary Output
LSD (low side driver) aux relay control,
75mA maximum (including attached
sensors)
Radio Properties
2.4 GHz, +8 dBm, Range dependent
on RF propagation variables such
as metal obstacles
Operating
Indoor, dry location
Environment
-4° to 149°F (-20° to 65°C)
Compliance
CSA certified, plenum rated,
FCC Part 15, CA IC
Mounting
1/2” knockout, screw tab, optional
mounting bracket supplied
Dimensions
9.4” L x 1.7” W x 1.18” H
10.1” L x 1.7” W x 1.18” H with
mounting bracket
Low Voltage
Max. recommended length of up
Wiring
to 100’ (30m)
Specifications
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation
or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the matter should be
referred to GE Current, a Daintree company.
Questions:
Web:
products.gecurrent.com
Phone:
1-866-855-8629
www.gecurrent.com
© 2021 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the
General Electric Company and are used under license. Information provided is subject to change without notice.
All values are design or typical values when measured under laboratory conditions.
DT110 (Rev. 04/29/2021
CAUTION
RISK OF EXPOSURE IF BATTERY IS REPLACED BY AN
INCORRECT TYPE. DISPOSAL OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
WGA100
This is a class A product. In domestic environments this product may
cause radio interference in which case the user may be required to
take adequate measures.
WARNING
