background image

Arize

®

 Factor 

Installation Guide

7

Connect the output of the driver to the first light bar using the 30” interconnection 

cable. The output of first light bar (6” cable) must be connected to the 30” cable of 

the 2nd lightbar, and so on. 

For ML900, only 2 lightbars should be connected as shown. 

For ML300, a minimum of 4, and a maximum of 6 light bars can be connected. 

Connect the shorting cap to the last 6” lightbar cable, as shown, or else the array will 

not light. The shorting cap must be secured such that it does not touch the light bar.

Shorting Cap Installation

ML900 Electrical Connection: 2 Lightbars only

Shorting Cap

ML 300 Electrical connection: 4, 5, or 6 Lightbars only

For all configurations greater than 5 bars, only use  3ft or 6ft extension cable (GECA30A14-AA03B  or 

GECA30A14-AA06B interconnection cables) in conjunction with LED Drivers without NEMA plugs 

(GEPSC210-600D-ADGNA-D1XA1  and  GEPSC210-600G-AGJNA-D1XA1).

600W

Driver

Lightbar 1

Interconnection cable

Lightbar 2

Shorting Cap

Shorting Cap

600W

Driver

Lightbar 1

Lightbar 3

Lightbar 2

Lightbar 4

Lightbar 5

Lightbar 6

ML300

ML900

Содержание GE Current Arize Factor











Отзывы: