Daikin VRV IV+ RXYTQ8U5YF страница 24 Скачать руководство пользователя

Страница: 24 / 144

Operation

Installer and user reference guide

RXYTQ

VRV IV+ heat pump for high ambient temperatures

4P561157-1B – 2021.11

7 Operation

In this chapter

7.1

Before operation ....................................................................................................................................................................

7.2

Operation range......................................................................................................................................................................

7.3

Operating the system .............................................................................................................................................................

7.3.1

About operating the system ..................................................................................................................................

7.3.2

About cooling, heating, fan only, and automatic operation .................................................................................

7.3.3

About the heating operation .................................................................................................................................

7.3.4

To operate the system (WITHOUT cool/heat changeover remote control switch) .............................................

7.3.5

To operate the system (WITH cool/heat changeover remote control switch).....................................................

7.4

Using the dry program............................................................................................................................................................

7.4.1

About the dry program ..........................................................................................................................................

7.4.2

To use the dry program (WITHOUT cool/heat changeover remote control switch)............................................

7.4.3

To use the dry program (WITH cool/heat changeover remote control switch) ...................................................

7.5

Adjusting the air flow direction..............................................................................................................................................

7.5.1

About the air flow flap ...........................................................................................................................................

7.6

Setting the master user interface ..........................................................................................................................................

7.6.1

About setting the master user interface ...............................................................................................................

7.6.2

To designate the master user interface (VRV DX and Hydrobox) .........................................................................

7.7

About control systems............................................................................................................................................................

7.1 Before operation

WARNING

This unit contains electrical and hot parts.

WARNING

Before operating the unit, be sure the installation has been carried out correctly by
an installer.

NOTICE

NEVER inspect or service the unit by yourself. Ask a qualified service person to
perform this work.

CAUTION

It is unhealthy to expose your body to the air flow for a long time.

CAUTION

To avoid oxygen deficiency, ventilate the room sufficiently if equipment with burner
is used together with the system.

CAUTION

Do NOT operate the system when using a room fumigation-type insecticide.
Chemicals could collect in the unit, and endanger the health of people who are
hypersensitive to chemicals.

NOTICE

Be sure to turn ON the power 6 hours before operation in order to have power
running to the crankcase heater and to protect the compressor.

Содержание VRV IV+ RXYTQ8U5YF
















































































































































Результаты поиска

Содержание VRV IV+ RXYTQ8U5YF

Отзывы:

Похожие инструкции для VRV IV+ RXYTQ8U5YF

Бренды по названию

Популярные бренды

Daikin VRV IV+ RXYTQ8U5YF, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VRV IV+ RXYTQ8U5YF

Отзывы:

Похожие инструкции для VRV IV+ RXYTQ8U5YF

Бренды по названию

Популярные бренды