background image

250FC
Total Heat Exchanger
HRV (Heat Reclaim Ventilation)
4P415946-1 – 2015.08

Installation manual

16

Procedure

1

Turn off the main switch of the HRV-1 and On/off controller.

2

Connect the air conditioner's remote controller.

3

Turn on the main switch of the HRV-1 and On/off controller.

4

Set the central control group number using the local setting on
the remote controller.

Mode No.: "00"
Central control group No.: "2-05"

5

Turn off the main switch of the HRV and On/off controller.

6

Disconnect the remote controller.

The setting is now complete.

For the ventilation air flow setting, follow the procedure described in
the section 

""All" control" on page 15

.

Zone control system

A maximum of 64 air conditioners and HRV units can be
connected to the F1 and F2 terminals.

The HRV units will turn on and off in according with the zone
operation command from the centralized controller.

Zone 2

The HRV units operate in the zone-linked mode, as described in the
section, 

"Linked control with more than two groups" on page 14

. For

the initial setting, follow the procedure described in that section.

It is necessary to assign a central control group number to each
HRV unit and air conditioner.
Regarding the setting of the group number, refer to the section on
"the centralized control group number setting" in the operating
instructions of the Centralized controller. Refer to the section

""All"/"individual" control" on page 15

 for the setting procedure.

For the ventilation air flow setting, follow the procedure
described in the section 

""All" control" on page 15

.

For the zone setting from the centralized controller, refer to the
operating instructions of the centralized controller.

The centralized controller can be used to control the individual
units in the zone for ventilation operation.

Remote control

Monitor of operation

The operation of the HRV can be monitored from the outside by the
connection of the adaptor PCB for remote control KRP50-2 (option).

Be sure to connect the terminal strip on the adaptor PCB for remote
control KRP50-2 (option).

P1

P2

P1 P2

P1 P2

HRV  1

1

2

1

Remote controller for air 
conditioner

2

Remote controller for HRV

F1 F2

F1 F2

F1 F2

F1 F2

F1 F2

P1 P2

P1

P2

P1 P2

P1

P2

HRV 1

HRV 2

HRV 3

VRV 

1

2

5

3

4

3

1

Zone 1

4

Connecting line can be extended 
up to 1000 m maximum

2

Zone 2

5

Centralized controller 
(DCS302B61

3

Remote controller for HRV

L

L · N

X10A
X9A

KRP50-2

1

2

3

1

2

5

3

4

6

1

Operation lamp

4

2P connecter

2

Power source

5

3P connecter

3

Power source

6

Printed circuit board

Wiring adapter for remote contact KRP50-2 (option)
(To be placed in the switch box of the HRV)

Содержание VAM250FC

























Отзывы: