manualshive.com logo in svg

Daikin RXQ10PY1, Руководство по обслуживанию

Поделиться
Скачать
Daikin RXQ10PY1 Скачать руководство пользователя страница 204

Appendix

SiEN34-705

198

General Information

7.14.4 Example 4: Pressure down Despite Absence of Leaks during Air 

Tight Test (All Model)

Situation

In order to carry out local air tight tests on the refrigerant piping the system was pressurized via 
the liquid pipe service port and after 24 hours the pressure was found to have fallen. The local 
refrigerant piping alone does not lose any pressure. Maybe the gas leak is supposed to be 
located in the indoor unit itself.

Source of 
Problem and 
Remedial Action

The system was pressurized from the liquid pipe side and the gas pipes were therefore not 
pressurized. The system was then left under pressure for 24 hours but during that time gas 
leaked through into the gas pipes due to internal leaks within electronic expansion valves and 
the gas pressure inside the liquid pipes consequently dropped.

Main Points

When carrying out air tight tests on local pipework 

it is essential that the system be 

pressurized via both the liquid pipes and the gas pipes

.

 

Outdoor unit

Indoor unit

Pressure gauge

Closed

Closed

Gas pipe

Liquid pipe

Nitrogen Gas

Electronic

expansion valve

Filter

Filter

Heat exchanger

Содержание RXQ10PY1




































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды