34
English
15.2.2. Mode 2
/QFGKUWUGFVQEJCPIGVJGƂGNFUGVVKPIUQHVJGU[UVGO%QPUWNVKPI
VJGEWTTGPVƂGNFUGVVKPIXCNWGCPFEJCPIKPIVJGEWTTGPVƂGNFUGVVKPI
value is possible.
In general, normal operation can be resumed without special interven-
VKQPCHVGTEJCPIKPIƂGNFUGVVKPIU
5QOGƂGNFUGVVKPIUCTGWUGFHQTURGEKCNQRGTCVKQPGIVKOGQRGTC
-
tion, recovery/vacuuming setting, adding refrigerant setting, etc.). In
such a case, it is required to abort the special operation before normal
QRGTCVKQPECPVYKNNDGKPFKECVGFKPDGNQYGZRNCPCVKQPU
=?
%QQN*GCVUGNGEVKQPUGVVKPI
Cool/Heat selection setting is used in case the optional
Cool/Heat selector (KRC19-26A) is used. Depending on the
outdoor unit setup (single outdoor unit setup or multi outdoor
unit setup), the correct setting should be chosen. More
details on how to use the Cool/Heat selector option can be
found in the manual of the Cool/Heat selector.
Default value=0.
• 0=Each individual outdoor unit can select Cool/Heat
operation (by Cool/Heat selector if installed).
• 1=Master unit decides Cool/Heat operation when outdoor
units are connected in multiple system combination (a)
• 2=Sub unit for Cool/Heat operation when outdoor units
are connected in multiple system combination (a)
%JCPIG=?QTKPHWPEVKQPQHTGSWKTGFHWPEVKQPCNKV[
=?
(QTEGFQRGTCVKQPQHKPFQQTWPKV
Default value=0.
Value
[2-6]
Description
0
OFF (default)
1
ON
=?
'EQNGXGNUGVVKPIHQT'EQOQFGXKC'ZVGTPCNEQPVTQNCFCRVQT
(Optional).
Value
[2-7]
Meaning
Level
0
Inactive (Default)
Ũ
1
Eco mode active by low
noise terminal short-
circuit
Standard
2
Eco mode active by
demand terminal short-
circuit
2-C short circuit = Low
3-C short circuit = Standard
Eco mode can be activated by short circuit the terminal on
'ZVGTPCNEQPVTQNCFCRVQT1RVKQPCNCEEQTFKPIVQ=?UGV
-
VKPI=?UJQWNFDGpq
This unit can operate with “T
e
or T
c
ƂZEQPVTQNqCPFp'EQ
mode”. Eco mode means “VRT” control.
+HVJGVGTOKPCNQPGZVGTPCNEQPVTQNCFCRVGTKUPQVEQPPGEVGF
D[UJQTVEKTEWKVYKVJ=?ůVJGU[UVGOQRGTCVGUCEEQTFKPI
VQ=?QT=?UGVVKPI
=?
6
e
target temperature during cooling operation
Default value=2.
Value
[2-8]
T
e
target
0
Auto
2
43°F (6°C) (default)
3
45°F (7°C)
4
46°F (8°C)
5
48°F (9°C)
6
50°F (10°C)
7
52°F (11°C)
%JCPIG=?KPHWPEVKQPQHTGSWKTGFQRGTCVKQP
method during cooling.
For more information and advice about the effect of these
settings, see 15.3. Energy saving and optimum operation on
RCIG|
=?
6
c
target temperature during heating operation
Default value=6.
Value
[2-9]
T
c
target
0
Auto
1
106°F (41°C)
3
109°F (43°C)
6
115°F (46°C) (default)
%JCPIG=?QTKPHWPEVKQPQHTGSWKTGFQRGTCVKQP
method during heating.
For more information and advice about the effect of these
settings, see 15.3. Energy saving and optimum operation on
RCIG|
=? 'PCDNGVJGNQYPQKUGHWPEVKQPCPFQTRQYGTEQPUWORVKQP
NKOKVCVKQPXKCGZVGTPCNEQPVTQNCFCRVQT&6##
If the system needs to run under low noise operation or
under power consumption limitation conditions when an
GZVGTPCNUKIPCNKUUGPVVQVJGWPKVVJKUUGVVKPIUJQWNFDG
changed. This setting will only be effective when the optional
GZVGTPCNEQPVTQNCFCRVQT&6##KUKPUVCNNGF
Default value=0.
6QCEVKXCVGVJKUHWPEVKQPEJCPIG=?
=? (CPJKIJUVCVKERTGUUWTGUGVVKPI
In order to increase the static pressure the outdoor unit fan
is delivering, this setting should be activated. For details
CDQWVVJKUUGVVKPIUGGVGEJPKECNURGEKƂECVKQPU
Default value=0.
6QCEVKXCVGVJKUHWPEVKQPEJCPIG=?
=? 2JCUGFKPUVCNNCVKQPUGVVKPI
Default value=0.
Value
[2-19]
Description
0
OFF (default)
1
ON
Conditions/rules apply for this setting. Refer to selection
software or contact your Daikin sales representative for
further details.
=? #FFKVKQPCNTGHTKIGTCPVEJCTIGQTYTQPIYKTKPICWVQOCVKE
detection
In order to activate the additional refrigerant charge amount
or wrong wiring automatic detection, the following setting
should be applied.
Default value=0.
6QCEVKXCVGCFFKVKQPCNTGHTKIGTCPVEJCTIG=?
Further instructions can be found in chapter 14.3. Method for
CFFKPITGHTKIGTCPVQPRCIG|
To stop the additional refrigerant charge operation (when
B(1B0DLQB959B,0LQGG