background image

Names and Functions

SiUS371901E

87

Remote Controller

4. Up button 

S

„

Used to raise the setpoint. 

„

The item above the current selection will be highlighted.
(The highlighted items will be scrolled continuously when the button is continuously pressed.)

„

Used to change the selected item.

5. Down button 

T

„

Used to lower the setpoint.

„

The item below the current selection will be highlighted.
(The highlighted items will be scrolled continuously when the button is continuously pressed.)

„

Used to change the selected item.

6. Right button 

X

„

Used to highlight the next items on the right-hand side.

„

Each screen is scrolled in the right-hand direction.

7. Left button 

W

„

Used to highlight the next items on the left-hand side.

„

Each screen is scrolled in the left-hand direction.

8. On/Off button 

„

Press this button and system will start.

„

Press this button again to stop the system.

9. Operation lamp

„

This lamp illuminates solid green during normal operation.

„

This lamp blinks if an error occurs.

10. Cancel button 

„

Used to return to the previous screen.

11. LCD (with backlight)

„

The backlight will be illuminated for approximately 30 seconds by pressing any button.

„

If two remote controllers are used to control a single indoor unit, only the controller accessed first will have 
backlight functionality.

Содержание REYQ-XA


























































































































































































































































































































































































































































Отзывы: