Daikin REMA5A7Y1B страница 50 Скачать руководство пользователя

Страница: 50 / 56

21 Troubleshooting

Installation and operation manual

REMA5+REYA8~20A7Y1B

VRV 5 heat recovery

4P684060-1 – 2022.02

Main
code

Sub code

Cause

Solution

SVEO

(a)

SVS

(b)

Master

Slave 1

Low pressure malfunction:

▪ Stop valve closed

▪ Refrigerant shortage

▪ Indoor unit malfunction

▪ Open stop valves.

▪ Check refrigerant recharge unit.

▪ Check the user interface's display or

transmission wiring between the outdoor
unit and the indoor unit.

Electronic expansion valve malfunction
(upper heat exchanger) (Y1E) – main PCB
(X21A)

Check connection on PCB or actuator.

Electronic expansion valve malfunction
(inverter cooling) (Y5E) – main PCB (X23A)

Check connection on PCB or actuator.

Electronic expansion valve malfunction
(lower heat exchanger) (Y3E) – main PCB
(X22A)

Check connection on PCB or actuator

Electronic expansion valve malfunction
(receiver gas) (Y4E) – main PCB (X25A)

Check connection on PCB or actuator.

Electronic expansion valve malfunction
(subcool heat exchanger) (Y2E) – main PCB
(X26A)

Check connection on PCB or actuator.

Discharge temperature too high (R21T) –
main PCB (X33A):

▪ Stop valve closed

▪ Refrigerant shortage

▪ Open stop valves.

▪ Check refrigerant recharge unit.

Compressor casing temperature too high
(R15T) – main PCB (X33A):

▪ Stop valve closed

▪ Refrigerant shortage

▪ Open stop valves.

▪ Check refrigerant recharge unit.

▪ Refrigerant overcharge

▪ Stop valve closed

▪ Check refrigerant recharge unit.

▪ Open stop valves.

Ambient temperature sensor malfunction
(R1T) – main PCB (X18A)

Check connection on PCB or actuator.

Discharge temperature sensor malfunction
(R21T): open circuit – main PCB (X33A)

Check connection on PCB or actuator.

Discharge temperature sensor malfunction
(R21T): short circuit - main PCB (X33A)

Check connection on PCB or actuator.

Compressor casing temperature sensor
malfunction (R15T): open circuit - main PCB
(X33A)

Check connection on PCB or actuator.

Compressor casing temperature sensor
malfunction (R15T): short circuit - main PCB
(X33A)

Check connection on PCB or actuator.

Suction compressor temperature sensor
(R12T) – sub PCB (X35A)

Check connection on PCB or actuator.

Suction temperature sensor (R10T) – main
PCB (X29A)

Check connection on PCB or actuator.

Heat exchanger deicer temperature sensor
(R11T) – sub PCB (X35A)

Check connection on PCB or actuator

Upper heat exchanger – gas - temperature
sensor (R8T) – main PCB (X29A)

Check connection on PCB or actuator.

Lower heat exchanger – gas - temperature
sensor (R9T) main PCB (X29A)

Check connection on PCB or actuator.

Liquid main - temperature sensor (R3T) –
main PCB (X30A)

Check connection on PCB or actuator.

Subcool heat exchanger – liquid -
temperature sensor (R7T) - main PCB
(X30A)

Check connection on PCB or actuator.

Subcool heat exchanger – liquid -
temperature sensor (R16T) - main PCB
(X35A)

Check connection on PCB or actuator.

Содержание REMA5A7Y1B
























































Результаты поиска

Содержание REMA5A7Y1B

Отзывы:

Похожие инструкции для REMA5A7Y1B

Бренды по названию

Популярные бренды

Daikin REMA5A7Y1B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание REMA5A7Y1B

Отзывы:

Похожие инструкции для REMA5A7Y1B

Бренды по названию

Популярные бренды