Daikin Modular L Smart Скачать руководство пользователя страница 23

Страница: 23 / 90

ESIE19-06

Part 2. Troubleshooting

2.2. Error based troubleshooting

21/01/20

Version 1.1

Page 23

Modular L Smart

2.2.1. HRV unit

2.2.1.1. “6A” – Damper motor malfunction

2.2.1.2. “60” – External protection device activated

Trigger

Effect

Reset

The limit switch of the damper motor did
not detect move of motor when energized
(3 times per minute).

Unit will not stop operating.
Control will disable output to damper
motor.

Power reset.
To remove warning from main history,
push the ON/OFF button on the remote
controller for 5 seconds in the check
mode.

Possible cause

Check

Corrective action

HRV unit - Electrical components

Faulty limit switch.

Check limit switch changes between open
and closed contact when power on HRV
unit.

Replace the damper motor assembly.

Faulty damper motor.

Check damper motor rotates when power
on HRV unit.

Replace the damper motor assembly.

Faulty main PCB.

Check HAP on main PCB is blinking.
Check connectors power and limit switch
damper motor.

Replace main PCB.
Reconnect plug(s) of power and limit
switch damper motor.

External factor (e.g. electrical noise) (error
disappears after power reset, but returns
after a while).

Check for source which could cause elec-
trical interference.

Avoid electrical interference.

Trigger

Effect

Reset

The input signal JC-C1 is set
28-8-02 or -03.

Unit will not stop operating.
Operation resume with (local) contact
opens again.

Automatic reset.
To remove warning from main history,
push the ON/OFF button on the remote
controller for 5 seconds in the check
mode.

Possible cause

Check

Corrective action

HRV unit - Electrical components

Local contact is closed.

Check state and wiring to local switch.

Change wiring.
Change local switch if contact permanent
closed.

Wrong field setting.

Check field setting by user interface.

Adjust field settings by user interface
according to installation lay out.

Faulty main PCB.

Check HAP on main PCB is blinking.

Replace main PCB.

External factor (e.g. electrical noise) (error
disappears after power reset, but returns
after a while).

Check for source which could cause elec-
trical interference.

Avoid electrical interference.

Содержание Modular L Smart



























































































Результаты поиска

Содержание Modular L Smart

Отзывы:

Похожие инструкции для Modular L Smart

Бренды по названию

Популярные бренды

Daikin Modular L Smart, Руководство по обслуживанию

Результаты поиска

Содержание Modular L Smart

Отзывы:

Похожие инструкции для Modular L Smart

Бренды по названию

Популярные бренды