background image

DV**PTC*14

 SERIES AIR HANDLERS

IOD-4021K
06/2021

Only personnel that have been trained to install, adjust, service 

or repair (hereinafter, “service”) the equipment specified in 

this manual should service the equipment. The manufacturer 

will not be responsible for any injury or property damage 

arising from improper service or service procedures.  If you 

service this unit, you assume responsibility for any injury or 

property damage which may result.  In addition, in jurisdictions 

that require one or more licenses to service the equipment 

specified in this manual, only licensed personnel should service 

the equipment.  Improper installation, adjustment, servicing 

or repair of the equipment specified in this manual, or 

attempting to install, adjust, service or repair the equipment 

specified in this manual without proper training may result in 

product damage, property damage, personal injury or death.

INSTALLATION INSTRUCTIONS

www.daikincomfort.com

 

Our continuing commitment to quality products may mean a change in specifications without notice.

19001 Kermier Road Waller, TX 77484

Index

1    Important Safety Instructions ................................................................ 2

2    Shipping Inspection ............................................................................... 3

2.1  Parts ...............................................................................................

3

2.2  Handling ..........................................................................................

3

3  Codes & Regulations ............................................................................. 3

4  Replacement Parts ................................................................................. 3

5  Pre-Installation Considerations ............................................................ 3

5.1  Preparation .....................................................................................

3

5.2  System Matches .............................................................................

3

5.3  Interconnecting Tubing ...................................................................

4

5.4  Clearances ......................................................................................

4

5.5  Horizontal Applications ...................................................................

4

6    Installation Location ......................................................... 4

6.1  Upflow Installation ...........................................................................

4

6.2  Horizontal Left Installation ..............................................................

4

6.3  Downflow/Horizontal Right Installation ...........................................

4

7    Refrigerant Lines .................................................................................... 6

7.1  Tubing Size .....................................................................................

6

7.2  Tubing Preparation .........................................................................

6

7.3  Tubing Connections for TXV Models ..............................................

7

7.4  Thermal Expansion Valve System Adjustment ...............................

8

8    Condensate Drain Lines .................................................. 8

9    Ductwork ......................................................................... 10

9.1  Thermal Expansion Valve System Adjustment ......................................

10

10  Return Air Filters .................................................................................. 10

11  Electric Heat .......................................................................................... 10

12   Electrical and Control Wiring ..............................................................11

12.1  Building Electrical Service Inspection ..........................................

11

12.2  Wire Sizing ...................................................................................

11

12.3  Maximum Overcurrent Protection (MOP) ....................................

11

12.4  Electrical Connections – Supply Voltage ....................................

12

12.4.1  Air Handler Only (Non-Heat Kit Models) ..................................

12

12.4.2  Air Handler - Non-Circuit Breaker Heat Kits .............................

12

12.4.3  Air Handler With Circuit Breaker Heat Kit ................................

12

12.5  Low Voltage Connections ...........................................................

12

13    Achieving 1.4% and 2.0% Airflow Low Leakage Rate

 ......................11

14    Start-Up Procedure ............................................................................. 12

15    Regular Maintenance ......................................................................... 12

16    Circulator Blower ................................................................................ 15

17    Troubleshooting ................................................................................. 17

 ©

 2014 - 2021

If  an “Ec” error is encountered on

startup, verify that the electric heater

DIP  switches  have  been  set  to  the

appropriate heater size.  See pages

14-17  for  the  heater  kit 

airflo

w

delivery and DIP switch 

se�ngs.

NOTICE

Содержание DV PTC 14 Series

































Отзывы: