Daikin MICROTECH 4 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 77

Daikin MICROTECH 4 Скачать руководство пользователя страница 67

67/77

Operation Manual

D

–EOMWC00A07-16_02EN

12.2.2

Navigation Mode

When the navigation wheel is turned clockwise, the cursor moves to the next line (down) on the p age. When the wheel is
turned counter-clockwise the cursor moves to the previous line (up) on the page. The faster the wheel is turned the faster
the cursor moves. Pushing the wheel acts as an “Enter” button.

Figure 11: Typical page layout

4 Main Menu 1



Evap LWT= 7.0°C

Time Until Restart



Cool LWT1 7.0°C

Figure 12: Parameter

4 Main Menu 1



Evap LWT= 7.0°C

Time Until Restart



Cool LWT1 7.0°C

Figure 13: Link to a sub-menu

4 Main Menu 1



Evap LWT= 7.0°C

Time Until Restart



Cool LWT1 7.0°C

Figure 14: Adjustable setpoint

For example, “Time Until Restart” jumps from level 1 to level 2 and stops there.

When the Back Button is pressed the display reverts back to the previously displayed page. If the Back button is repeat ed
pressed the display continues to revert one page back along the current navigation path until the “main menu” is reached.

When the Menu (Home) Button is pressed the display reverts to the “main page.”

When the Alarm Button is depressed, the Alarm Lists menu is displayed.

12.2.3

Edit Mode

The Editing Mode is entered by pressing the navigation wheel while the cursor is pointing to a line containing an editable
field.  Once  in  the  edit  mode  pressing  the  wheel  again  causes  the  editable  field  to  be  highlighted.  Turning  the  wheel
clockwise while  the editable field is highlighted causes the value to be increased. Turning the wheel counter -clockwise
while the editable field is highlighted causes the value to be decreased. The faster the wheel is turned the faster the value
is increased or decreased. Pressing the wheel again cause the new value to be saved and the keypad/display to leave the
edit mode and return to the navigation mode.

4 Main Menu 1



Evap LWT= 7.0°C
Time Until Restart



Cool LWT1 7.0°C

Line number

Access level

Alarm bell

«
...
65
66
67
68
69
...
»

Содержание MICROTECH 4














































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды