11
/ English
Care and Cleaning
■
■
■
■
Cleaning the front panel
•
Clean as necessary
When used in areas which are very dirty, the cleaning frequency
will increase.
•
Wipe off any dirt using a rag or wet tissue.
•
If the dirt cannot be removed, wipe off using a rag soaked in a
neutral household cleaner.
ATTENTION
•
Be careful not to scratch the front or
damage the rear protrusions of the
removed front panel.
In particular, the rear protrusions func-
tion as a safety switch to turn OFF the
power if the front panel is opened.
If damaged, the unit will not operate.
•
Do not use gasoline, benzine, thinner,
polishing powder or light oil.
Color changes or deformation may
occur.
•
Do not use a metal brush.
Scratches may occur.
■
■
■
■
Cleaning the dust sensor
•
Clean any dust clogging the air intake for the dust sensor.
•
Clean using nozzles for small spaces of an electric vacuum
cleaner.
■
■
■
■
Sensitivity settings of the dust sensor
The sensitivity of the dust sensor may worsen or become too sensitive.
This is because the response time of the dust sensor differs depending
on size of the room and installation location. For example, if installed at
a low position in the room, the response for cigarette smoke will worsen.
For this case, try installing the unit at a high position such as on a rack. If
the response is still poor even though the installation location is
changed, change the sensitivity of the dust sensor following the next
method.
1. Press the
“
”
[Operation switch/Stop] button of the
main unit for 10 seconds.
2. While pressing the
“
”
[Operation switch/Stop] button
of the main unit point the remote controller at the main
unit and press the
“
”
[OFF TIMER] button.
The receive sound will beep and after
“
”
L (Low),
“
”
M (Standard) or
“
”
H (High) flashes for approximately 5 sec-
onds, a lamp will light corresponding to the currently set sensitivity.
3. Change the settings using the
“
”
[Operation switch/
Stop] button of the main unit.
Switches each time it is pressed.
The settings is shown in the airflow rate indicator.
4. When you decide on the settings, point the remote con-
troller at the main unit and press the
“
”
[OFF TIMER]
button.
The receive sound will beep and the setting lamp will flash.
5. Unplug the power plug one time and then after 3 sec-
onds or more plug it in again.
This completes the settings.
NOTE
•
If the operation of
5
. is not performed, the unit will not return to nor-
mal operation mode. If the operation of
5
. is performed, during the
settings, the settings will not be correct.
•
When the sensitivity is set high, it will become difficult for the sensor
lamp to go out.
■
■
■
■
Optional accessories
Replacement Titanium apatite photocatalytic filter roll and the wall-hang
kit are available at your dealer.
■
■
■
■
Disposal requirements
Your Daikin product is marked with this symbol. This
means that electrical and electronic products shall not
be mixed with unsorted household waste.
Disposal of this product must be done in accordance
with relevant local and national legislation. By disposing
of this product correctly, you will help ensure its proper
treatment, recovery and recycling, thus preventing
potential negative consequences for the environment and human health.
Please contact your local authority for more information.
Batteries must be removed from the remote controller and disposed of
separately in accordance with relevant local and national legislation.
Rear side
Protrusion
Air intake for dust sensor
Part name
Part number
Replacement Titanium apatite photocatalytic filter roll
BAC959A4
Wall-hanging kit
KKK13A
Airflow speed
display
Dust sensor
sensitivity
High
(Sensor display
becomes easy
to light.)
Normal
(setting when
shipped)
Low
(Sensor display
will have difficulty
coming on.)
“
”
L (
Low)
“
”
M (
Standard)
“
”
H (
High)
Airflow rate indicator
Off timer button
Operation switch / stop
button
Содержание MC704AVM
Страница 14: ...0508 HT 3P068886 10R M03B106C...
