manualshive.com logo in svg

Daikin IM 1068-2, Установка и обслуживание данных

Поделиться
Скачать
Daikin IM 1068-2 Скачать руководство пользователя страница 9

IM 1068-2 / Page 9 of 28

Installation

3.  Manually spin the condenser fan wheel to be sure that 

there is no interference or looseness. If it is loose, tighten 

the setscrew located over the center of the flat on the 

motor shaft. Do not lubricate condenser fan motor at time 

of installation.

4.  Slide the chassis into the wall box. Chassis must be square 

in the box so that all the rubber seals are pressed tight. 

Check bottom seal between chassis and wall box to ensure 

that it has not been unseated from slot during chassis 

installation.

Cooling Chassis Installation

1.  Remove the cooling chassis from the shipping carton 

and examine it for damage. Do not rest it on end. Check 

the plate rating against the power supply to make sure 

that they are the same (Figure 14). Also check the size 

(capacity) to make sure that it coincides with the heat 

section; e.g., Size 009 cooling.

2.  The cooling chassis is supplied with an internal spring 

mounted compressor. The hold-down nuts on the 

compressor mountings should not be loosened.

Figure 14: Cooling Chassis Details

Содержание IM 1068-2





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды