background image

125A8V1BF

VRV IV System indoor unit

4P405267-1C – 2021.04

Installation and operation manual

19

Operation  example

:  Schedule  timer  based  on  temperature  set

points.
When setback function (refer to 

"[2] Automatic setback function" on

page 19

) is enabled, the setback operation will have priority over the

scheduled action in the schedule timer.

Operation example

: Schedule timer based on ON/OFF instruction.

When setback function (refer to 

"[2] Automatic setback function" on

page 19

) is enabled, the setback operation will have priority over the

scheduled action in the schedule timer if ON instruction is active. If

OFF  instruction  is  active  this  will  have  priority  over  the  setback

function. At any time the OFF instruction will have the highest priority.

[0

-

04]

  Status:  defines  whether  the  ON/OFF  instruction  can  be

used in the schedule timer for cooling.

Same as for [0

-

03] but for cooling schedule timer.

For cooling, no setback function is available.

[1] Settings are not applicable
[2] Automatic setback function

Setback  function  provides  the  possibility  to  lower  the  room

temperature.  The  setback  function  can  for  instance  be  activated

during the night because the temperature demands during night and

day are not the same.

[2

-

00] 

Status: defines whether the setback function is turned ON

(1) or OFF (0)

[2

-

01]

 Start time: time at which setback is started

[2

-

02]

 Stop time: time at which setback is stopped

Setback  can  be  configured  for  both  room  temperature  control  and

leaving water temperature control.

1

Schedule timer

2

Setback function

3

When both setback function and schedule timer are enabled

A

Setback function

t

Time

T

Temperature set point
Room temperature

Leaving water temperature

Method 2

Space heating based on ON/OFF instruction

During operation When the schedule timer switches space heating OFF, 

the controller will be switched off (operation LED will stop 

working). 

When pushing 

the 

 button

The schedule timer for space heating will stop (when 

active at that moment) and will start again at the next 

scheduled ON function.

The "last" programmed command overrules the 

"preceding" programmed command and will remain 

active until the "next" programmed command occurs.

Example: imagine the actual time is 17:30 and 

actions are programmed at 13:00, 16:00 and 

19:00. The "last" programmed command 

(16:00) overruled the "previous" programmed 

command (13:00) and will remain active until 

the "next" programmed command (19:00) 

occurs.

So in order to know the actual setting, one should consult 

the last programmed command. It is clear that the "last" 

programmed command may date from the day before. 

Refer to the operation manual.

The controller will be switched off (operation LED will 

stop working).

However the schedule timer icon will stay displayed.

When pushing 

the 

 button

The schedule timer for space heating will be stopped and 

will not start again.

The schedule timer icon will not be displayed anymore.

T

t

6:30 9:00

16:00

0:30

19C

19C

19C

22C

21C

42C

42C

42C

45C

44C

42C

19C

19C

19C

22C

21C

42C

42C

45C

44C

0:30

1

T

t

18C

37C

37C

18C

A

5:00

23:00

5:00

23:00

2

T

t

5:00

9:00

16:00

23:00

19C

18C

19C

22C

21C

42C

40C

42C

45C

44C

40C

19C

18C

19C

22C

21C

42C

19C

19C
42C

19C
42C

19C

19C

19C
42C

45C

44C

6:30

3

37C

37C

40C

40C

1

Schedule timer

2

Setback function

3

When both setback function and schedule timer are enabled

A

Setback function

B

ON/OFF instruction

t

Time

T

Temperature set point
Room temperature

Leaving water temperature

INFORMATION

By default the setback function is enabled.

The  setback  function  can  be  combined  with  the

automatic weather dependent set point operation.

Setback  function  is  an  automatic  daily  scheduled

function.

t

18C
40C

40C

18C

A

5:00

23:00

5:00

23:00

2

B

t

9:00

16:00

19C

19C

22C

21C

42C

42C

45C

44C

19C

19C

22C

21C

42C

42C

45C

44C

1

OFF

ON

ON

6:30

0:30

B

t

6:30

9:00

16:00

23:00

19C

19C

22C

21C

42C

42C

45C

44C

19C

19C

22C

21C

42C

42C

45C

44C

3

OFF

ON

ON

18C
40C

40C

18C

Содержание HXY080A8V1BF

















































Отзывы: