Daikin HXY080A7V1B Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 48

Daikin HXY080A7V1B Скачать руководство пользователя страница 6

Installation and operation manual

4

125A7V1B

VRV IV System indoor unit

4P325971-1B – 2012.07

2.2.6.

Meaning of used items

3. About the box



At delivery, the unit must be checked for damage. Any damage
must be reported immediately to the carrier’s claims agent.



Bring the packed unit as close as possible to its final installation
position to prevent damage during transport.

3.1.

Indoor unit

3.1.1.

To unpack the indoor unit

a

Installation/operation manual

3.1.2.

To remove the accessories from the indoor unit

The installation/operation manual indoor unit is located in the upper
part of the box. Follow the procedure below to remove the other
accessories.

1

Unfix front panel.

2

Tilt the bottom side of the front panel upwards and remove it.

Dealer:

Sales distributor for the product.

Authorized installer:

Technical skilled person who is qualified to install the product.

User:

Person who is owner of the product and/or operates the product.

Applicable legislation:

All international, European, national and local directives, laws,
regulations and/or codes that are relevant and applicable for a
certain product or domain.

Service company:

Qualified company which can perform or coordinate the required
service to the product.

Installation manual:

Instruction manual specified for a certain product or application,
explaining how to install, configure and maintain it.

Operation manual:

Instruction manual specified for a certain product or application,
explaining how to operate it.

Accessories:

Labels, manuals, information sheets and equipment that are
delivered with the product and that need to be installed
according to the instructions in the accompanying
documentation.

Optional equipment:

Equipment made or approved by Daikin that can be combined
with the product according to the instructions in the
accompanying documentation.

Field supply:

Equipment not made by Daikin that can be combined with the
product according to the instructions in the accompanying
documentation.

INFORMATION

Do NOT throw away the upper cardboard cover. On the
inside of the cardboard cover, the installation pattern is
printed.

WARNING

Tear apart and throw away plastic packaging bags so that
children will not play with them. Children playing with
plastic bags face danger of death by suffocation.

a

2

1

«
...
4
5
6
7
8
...
»

Содержание HXY080A7V1B

















































Отзывы:

Нет отзывов