background image

6

English

Indoor Unit 

3.

Installing indoor unit.

3-1. Right-side, right-back, or right-bottom piping.

1) Attach the drain hose to the underside of the refrigerant pipes with 

adhesive vinyl tape.

2) Wrap the refrigerant pipes and drain hose together with insulation 

tape.

3) Pass the drain hose and refrigerant pipes through the wall hole, 

then set the indoor unit on the mounting plate hooks by using the 

 markings at the top of the indoor unit as a guide.

4) Open the front panel, then open the service lid. 

(Refer to Installation Tips)

5) Pass the interconnecting wires from the outdoor unit through the 

feed-through wall hole and then through the back of the indoor 
unit. Pull them through the front side.  Bend the ends of tie wires 
upward in advance for easier work. (If the interconnecting wire 
ends are to be stripped first, bundle wire ends with adhesive 
tape.)

6) Press the indoor unit’s bottom panel with both hands to set it 

on the mounting plate hooks. Make sure the wires do not catch 
on the edge of the indoor unit.

3-2. Left-side, left-back, or left-bottom piping.

1) Attach the drain hose to the underside of the refrigerant pipes 

with adhesive vinyl tape.

2) Be sure to connect the drain hose to the drain port in place of a 

drain plug.

3) Shape the refrigerant pipe along the pipe 

path marking on the mounting plate.

4) Pass drain hose and refrigerant pipes 

through the wall hole, then set the indoor 
unit on mounting plate hooks, using the 

 markings at the top of indoor unit as a 

guide.

5) Pull in the interconnecting wires.
6) Connect the inter-unit piping.

Right-bottom 
piping

Right-back piping

Right-side piping

Bind coolant pipe 
and drain hose 
together with 
insulating tape.

Remove pipe port cover 
here for right-side piping

Remove pipe port cover 
here for right-bottom piping

Mounting plate

A

Wire guide

When stripping the 
ends of interconnecting 
wires in advance, bind 
right ends of wires with 
insulating tape.

Hang indoor unit’s hook here.

Interconnecting
wires

Mounting plate

A

Remove pipe port cover here for left-bottom piping

Remove pipe 
port cover 
here for left-
side piping

Left-bottom piping

Left-side 
piping

Left-back 
piping

No gap

Do not apply lubricating 
oil (refrigerant machine 
oil) when inserting.
Application of causes 
deterioration and drain 
leakage of the plug.

Insert a hexagon wrench (4mm)

How to set drain plug

Interconnecting wires

Drain hose

Caulk this hole 
with putty or 
caulking material.

Wrap insulating tape around the 
bent portion of refrigerant pipe.
Overlap at least half the width of 
the tape with each turn.

Bind with 
plastic tape.

Thermistor cable

 A  Mounting plate

01_EN_3P211822-1C.fm  Page 6  Tuesday, November 27, 2007  6:30 PM

Содержание FTYN25GXV1B

















Отзывы: