background image

7

English

Indoor Unit Installation

3-2. Left-side, left-back, or left-bottom piping

How to replace the drain plug and drain hose

• 

Replacing onto the left side

1) Remove the insulation fixing screw on the right 

and remove the drain hose.

2) Remove the drain plug on the left side and 

attach it to the right side.

3) Insert the drain hose and tighten with included 

insulation fixing screw.
* (Forgetting to tighten this may cause water 

leakages.)

Drain hose attachment position

* The drain hose is on the back of the unit.

Front side of unit

Attachment on the right side (factory default)

Attachment on the left side

Drain hose

Drain hose

Insulation 

fixing screw

Insulation 

fixing screw

Right side

Left side

1) Attach the drain hose to the underside of the refrigerant pipes 

with adhesive vinyl tape.

Remove pipe port cover here for left-bottom piping.

Remove pipe 
port cover 
here for left-
side piping.

Left-bottom piping

Left-side 
piping
Left-back 
piping

2) Be sure to connect the drain hose to the drain port in place of a 

drain plug.

How to set drain plug

No gap.

Do not apply lubricating 
oil (refrigeration oil) 
when inserting.
Application of causes 
deterioration and drain 
leakage of the plug.

Insert a hexagonal wrench (4mm).

3) Shape the refrigerant pipe along the pipe 

path marking on the mounting plate.

4) Pass drain hose and refrigerant pipes 

through the wall hole, then set the indoor 
unit on mounting plate hooks, using the   
markings at the top of indoor unit as a 
guide.

5) Pull in the inter-unit wire.
6) Connect the inter-unit pipes.

Drain 

hose

Caulk this hole 

with putty or 

caulking material.

Bind with adhesive 
vinyl tape.

 A Mounting plate

Wrap insulating tape around the 
bent portion of refrigerant pipe. 
Overlap at least half the width of 
the tape with each turn.

7) Wrap the refrigerant pipes and drain hose together with insulation tape 

as right figure, in case of setting the drain hose through the back of the 
indoor unit.

8) While exercising care so that the inter-unit wire do not catch indoor unit, 

press the bottom edge of indoor unit with both hands until it is firmly 
caught by the mounting plate hooks. Secure indoor unit to the mounting 
plate with indoor unit fixing screws (M4 × 12L).

Refrigerant
pipes

Drain hose

Bottom frame

F  Indoor unit fixing screw

  (M4 × 12L) (2 points)

Mounting
plate

A

Inter-unit wire

3-3. Wall embedded piping

Follow the instructions given under left-side, left-back, or left-bottom piping.
1) Insert the drain hose to this depth so it won’t be pulled out of the drain 

pipe.

Inner wall

Vinyl chloride 
drain pipe 
(VP-30)

Drain hose

50mm 
or more

Insert drain hose 
to this depth so 
it won’t be pulled 
out of drain pipe.

Outer wall

01_EN_3P297034-1.indd   7

10/12/2011   11:37:03 AM

Содержание FTXS20K2V1B


















Отзывы: