background image

English

English

6

• Remove the pipe port cover as shown below.

1) Cut off the pipe port cover from inside the front grille using a copping 

saw. 
Apply the blade of the copping saw to the notch, and cut off the pipe 
port cover along the slit.

2) After cutting off the pipe port cover, perform filing. Remove the burrs 

along the cut section using a half round needle file.

CAUTION

• If the pipe port cover is cut off using nippers, the front grille will be damaged. Please do not use nippers.
• Wear gloves during the pipe port cover removal.

3-1. Right-side, right-back, or right-bottom piping

1) Attach the drain hose to the underside of the refrigerant pipes with 

adhesive vinyl tape.

2) Wrap the refrigerant pipes and drain hose together with insulation 

tape.

Right-bottom 
piping

Right-back piping

Bind coolant pipe 
and drain hose 
together with 
insulating tape.

Remove pipe port cover 
here for right-side piping.

Remove pipe port cover 
here for right-bottom piping.

3) Pass the drain hose and refrigerant pipes through the wall hole, 

then set the indoor unit on the mounting plate hooks by using the 
markings at the top of the indoor unit as a guide.

Mounting plate

A

4) Open the front panel, then open the service lid.  

(Refer to preparation before installation.)

5) Pass the inter-unit wire from the outdoor unit through the 

feed-through wall hole and then through the back of the indoor 
unit. Pull them through the front side. Bend the ends of tie 
wires upward for easier work in advance. (If the inter-unit wire 
ends are to be stripped first, bundle wire ends with adhesive 
tape.)

6) Press the bottom frame of the indoor unit with both hands to 

set it on the mounting plate hooks. Make sure the wires do not 
catch on the edge of the indoor unit.

Wire guide

When stripping the 
ends of inter-unit wire 
in advance, bind right ends 
of wires with insulating tape.

Hang indoor unit’s hook here.

Inter-unit wire

Mounting plate

A

01_EN_3P297034-1.indd   6

10/12/2011   11:37:02 AM

Содержание FTXS20K2V1B


















Отзывы: