Daikin ETVX16E9W7, Руководство по установке

Страница: 25 / 40

7 Configuration
Installation manual
25
ETVH/23E
Daikin Altherma 3 H HT F
4P644728-1B – 2022.03
▪ In Weather dependent LWT setpoint mode, the scheduled
actions consist of desired shift actions, either preset or custom.
# Code Description
[2.1] N/A ▪ 0: No
▪ 1: Yes
7.2.6 Configuration wizard: Additional zone
The most important settings for the additional leaving water zone
can be set here.
Emitter type
For more info about this functionality, see "7.2.5 Configuration
wizard: Main zone" [
4
24].
# Code Description
[3.7] [2‑0D] ▪ 0: Underfloor heating
▪ 1: Fancoil unit
▪ 2: Radiator
Control
The control type is displayed here, but cannot be adjusted. It is
determined by the control type of the main zone. For more info about
the functionality, see
"7.2.5 Configuration wizard: Main zone" [
4
24].
# Code Description
[3.9] N/A ▪ 0: Leaving water if the control type
of the main zone is Leaving water .
▪ 1: External room thermostat if the
control type of the main zone is
External room thermostat or Room
thermostat .
Setpoint mode
For more info about this functionality, see "7.2.5 Configuration
wizard: Main zone" [
4
24].
# Code Description
[3.4] N/A ▪ 0: Fixed
▪ 1: WD heating, fixed cooling
▪ 2: Weather dependent
If you choose
WD heating, fixed cooling
or
Weather
dependent , the next screen will be the detailed screen with weather-
dependent curves. Also see "7.3 Weather-dependent curve" [
4
26].
Schedule
Indicates if the desired leaving water temperature is according to a
schedule. Also see
"7.2.5 Configuration wizard: Main zone" [
4
24].
# Code Description
[3.1] N/A ▪ 0: No
▪ 1: Yes
7.2.7 Configuration wizard: Tank
INFORMATION
To make tank defrost possible, we recommend a minimum
tank temperature of 35°C.
Heat up mode
The domestic hot water can be prepared in 3 different ways. They
differ from each other by the way the desired tank temperature is set
and how the unit acts upon it.
# Code Description
[5.6] [6-0D] Heat up mode :
▪ 0: Reheat only : Only reheat
operation is allowed.
▪ 1: Sc reheat : The domestic
hot water tank is heated according to a
schedule and between the scheduled
heat up cycles, reheat operation is
allowed.
▪ 2: Schedule only : The domestic hot
water tank can ONLY be heated
according to a schedule.
See the operation manual for more details.
Settings for Reheat only mode
During Reheat only mode, the tank setpoint can be set on the user
interface. The maximum allowed temperature is determined by the
following setting:
# Code Description
[5.8] [6-0E] Maximum :
The maximum temperature that users
can select for the domestic hot water.
You can use this setting to limit the
temperature at the hot water taps.
The maximum temperature is NOT
applicable during disinfection function.
See disinfection function.
To set the heat pump ON hysteresis:
# Code Description
[5.9] [6-00] Heat pump ON hysteresis
▪ 2°C~40°C
Settings for Schedule only mode and Sc reheat mode
Comfort setpoint
Only applicable when domestic hot water preparation is
Schedule
only or Sc reheat . When programming the schedule, you
can make use of the comfort setpoint as a preset value. When you
later want to change the storage setpoint, you only have to do it in
one place.
The tank will heat up until the storage comfort temperature has
been reached. It is the higher desired temperature when a storage
comfort action is scheduled.
Additionally, a storage stop can be programmed. This feature puts a
stop to tank heating even if the setpoint has NOT been reached.
Only program a storage stop when tank heating is absolutely
undesirable.
# Code Description
[5.2] [6-0A] Comfort setpoint :
▪ 30°C~[6‑0E]°C
Eco setpoint
The storage economic temperature denotes the lower desired
tank temperature. It is the desired temperature when a storage
economic action is scheduled (preferably during day).
# Code Description
[5.3] [6-0B] Eco setpoint :
▪ 30°C~min(50,[6‑0E])°C
Reheat setpoint
Desired reheat tank temperature , used: