Daikin ETVH16S23EA6V, Руководство по эксплуатации

Страница: 19 / 24

8 Troubleshooting
Operation manual
19
ETVH/X16S(U)18+9W + ETBH/9W
Daikin Altherma 3 H HT F+W
4P644732-1 – 2021.02
8.3 Symptom: You are feeling too cold
(hot) in your living room
Possible cause Corrective action
The desired room temperature is
too low (high). Increase (decrease) the desired
room temperature. See
"5.6.2 To
change the desired room
temperature"
[
4
12].
If the problem recurs daily, do
one of the following:
▪ Increase (decrease) the room
temperature preset value. See
the user reference guide.
▪ Adjust the room temperature
schedule. See "5.8 Schedule
screen: Example" [
4
14].
The desired room temperature
cannot be reached. Increase the desired leaving
water temperature in accordance
with the heat emitter type. See
"5.6.3 To change the desired
leaving water temperature"
[
4
12].
The weather-dependent curve is
set incorrectly. Adjust the weather-dependent
curve. See
"5.9 Weather-
dependent curve" [
4
15].
8.4 Symptom: The water at the tap is
too cold
Possible cause Corrective action
You ran out of domestic hot
water because of unusual high
consumption. If you immediately need domestic
hot water, activate the DHW tank
Powerful operation . However,
this consumes extra energy. See
"5.7.4 Using DHW powerful
operation"
[
4
13].
If the problems recurs daily, do
one of the following:
▪ Increase the DHW tank
temperature preset value. See
the user reference guide.
▪ Adjust the DHW tank
temperature schedule.
Example: Program to
additionally heat up the
DHW tank to a preset value
(
Eco setpoint = lower tank
temperature) during the day.
See
"5.8 Schedule screen:
Example" [
4
14].
The desired DHW tank
temperature is too low.
8.5 Symptom: Heat pump failure
When the heat pump fails to operate, the backup heater and/or
booster heater can serve as an emergency heater. It then takes over
the heat load either automatically or by manual interaction.
▪ When Emergency is set to Automatic and a heat pump failure
occurs:
▪ For ETVH/X: The backup heater automatically takes over the
domestic hot water production and space heating.
▪ For ETBH/X: The backup heater automatically takes over the
heat load, and the booster heater in the optional tank takes over
the domestic hot water production.
▪ When Emergency is set to Manual and a heat pump failure
occurs, the domestic hot water heating and space heating stops.
To manually recover it via the user interface, go to the
Malfunctioning
main menu screen and confirm whether the
backup heater and/or booster heater can take over the heat load
or not.
▪ Alternatively, when Emergency is set to:
▪ auto SH reduced/DHW on , space heating is reduced but
domestic hot water is still available.
▪
auto SH reduced/DHW off
, space heating is reduced and
domestic hot water is NOT available.
▪ auto SH normal/DHW off , space heating operates as
normally but domestic hot water is NOT available.
Similarly as in Manual mode, the unit can take the full load with
the backup heater and/or booster heater if the user activates this
via the
Malfunctioning main menu screen.
When the heat pump fails, or will appear on the user
interface.
Possible cause Corrective action
Heat pump is damaged. See "8.1 To display the help text
in case of a malfunction" [
4
18].
INFORMATION
When the backup heater or booster heater takes over the
heat load, electricity consumption will be considerably
higher.
8.6 Symptom: The system is making
gurgling noises after
commissioning
Possible cause Corrective action
There is air in the system. Purge air from the system. (a)
Incorrect hydraulic balance. 1 Perform hydraulic balancing
to assure that the flow is
correctly
distributed
between the emitters.
2 If hydraulic balancing is not
sufficient, change the pump
limitation settings ([9-0D]
and [9-0E] if applicable).
Various malfunctions.
Check if or is displayed
on the home screen of the user
interface. See
"8.1 To display the
help text in case of a
malfunction"
[
4
18] for more
information about the
malfunction.
(a)
We recommend to purge air with the air purge function of the unit
(to be performed by the installer). If you purge air from the heat
emitters or collectors, mind the following:
WARNING
Air purging heat emitters or collectors. Before you
purge air from heat emitters or collectors, check if or
is displayed on the home screen of the user interface.
▪ If not, you can purge air immediately.
▪ If yes, make sure that the room where you want to
purge air is sufficiently ventilated. Reason: Refrigerant
might leak into the water circuit, and subsequently into
the room when you purge air from the heat emitters or
collectors.