background image

11 Maintenance and service

Installer reference guide

75

ERGA04~08DAV3(A) + 08S18+23DA
Daikin Altherma – Low temperature split
4P495249-1 – 2017.12

▪ Dirty water coming out of the relief valve:

▪ open the valve until the discharged water does NOT contain dirt

anymore

▪ flush the system

To make sure this water originates from the tank, check after a tank
heat up cycle.

It is recommended to do this maintenance more frequently.

Pressure relief valve hose

Check  whether  the  pressure  relief  valve  hose  is  positioned
appropriately  to  drain  the  water.  See 

"7.8.5  To  connect  the  drain

hose to the drain" on page 35

.

Relief valve of the domestic hot water tank (field supply)

Open the valve and check the correct operation. 

Water may be very

hot!

Checkpoints are:

▪ The  water  flow  coming  from  the  relief  valve  is  high  enough,  no

blockage of the valve or in between piping is suspected.

▪ Dirty water coming out of the relief valve:

▪ open the valve until the discharged water does not contain dirt

anymore

▪ flush and clean the complete tank, including the piping between

the relief valve and cold water inlet.

To make sure this water originates from the tank, check after a tank
heat up cycle.

It is recommended to do this maintenance more frequently.

Switch box

▪ Carry out a thorough visual inspection of the switch box and look

for obvious defects such as loose connections or defective wiring.

▪ Using  an  ohmmeter,  check  if  contactors  K1M,  K2M  and  K3M

operate correctly. All contacts of these contactors must be in open
position when the power is turned OFF.

WARNING

If  the  internal  wiring  is  damaged,  it  has  to  be  replaced  by
the  manufacturer,  its  service  agent  or  similarly  qualified
persons.

Descaling

Depending on water quality and set temperature, scale can deposit
on  the  heat  exchanger  inside  the  domestic  hot  water  tank  and  can
restrict  heat  transfer.  For  this  reason,  descaling  of  the  heat
exchanger may be required at certain intervals.

Chemical disinfection

If  the  applicable  legislation  requires  a  chemical  disinfection  in
specific situations, involving the domestic hot water tank, please be
aware that the domestic hot water tank is a stainless steel cylinder.
We  recommend  to  use  a  non-chloride  based  disinfectant  approved
for use with water intended for human consumption.

NOTICE

When  using  means  for  descaling  or  chemical  disinfection,
it must be ensured that the water quality remains compliant
with EU directive 98/83 EC.

11.4.1

To drain the domestic hot water tank

DANGER: RISK OF BURNING

The water in the tank can be very hot.

Prerequisite: 

Turn OFF the unit via the user interface.

Prerequisite: 

Turn OFF the respective circuit breaker.

Prerequisite: 

Close the cold water supply.

Prerequisite: 

Open  all  the  hot  water  tapping  points  to  allow  air  to

enter the system.

1

Remove  the  top  panel,  the  user  interface  panel  and  the  front
panel.

2

Lower the switch box.

3

Remove the stop from the access point to the tank.

4

Use a drain hose and a pump to drain the tank via the access
point.

a

a

Access point to the tank

11.5

About cleaning the water filter in
case of trouble

INFORMATION

For  yearly  maintenance,  you  do  not  have  to  remove  the
water  filter  from  the  unit  to  clean  it.  But  in  case  of  trouble
with  the  water  filter,  you  might  have  to  remove  it  so  that
you  can  thoroughly  clean  it.  Then  you  need  to  do  as
follows:

"11.5.1 To remove the water filter" on page 75

"11.5.2  To  clean  the  water  filter  in  case  of  trouble"  on
page 76

"11.5.3 To install the water filter" on page 76

11.5.1

To remove the water filter

Prerequisite: 

Turn OFF the unit via the user interface.

Prerequisite: 

Turn OFF the respective circuit breaker.

1

The water filter is located behind the switch box. To get access
to it, see:

"7.2.3 To open the indoor unit" on page 24

"7.2.5  To  lower  the  switch  box  on  the  indoor  unit"  on
page 25

2

Close the stop valves of the water circuit.

3

Close  the  valve  (if  equipped)  of  the  water  circuit  towards  the
expansion vessel.

4

Remove the cap on the bottom of the water filter.

5

Connect a drain hose to the bottom of the water filter.

6

Open  the  valve  on  the  bottom  of  the  water  filter  to  drain  water
from the water circuit. Collect the drained water in a bottle, sink,
… using the installed drain hose.

7

Remove the 2 clips that fix the water filter.

Содержание ERGA06DAV3





































































































Отзывы: