EKHBRD011~Y1
Indoor unit for air to water heat pump system
4PW60970-1B
Installation manual
12
Guidelines for flare connection
■
Flares should not be re-used. New ones should be made in
order to prevent leaks.
■
Use a pipe cutter and flare tool suitable for the refrigerant used.
■
Only use the annealed flare nuts included with the unit. Using
different flare nuts may cause the refrigerant to leak.
■
Please refer to the table for flaring dimensions and tightening
torques (too much tightening will result in splitting the flare).
■
When connecting the flare nut, coat the flare inner surface with
ether oil or ester oil and initially tighten 3 or 4 turns by hand
before tightening firmly.
■
When loosening a flare nut, always use two wrenches together.
When connecting the piping, always use a spanner and torque
wrench together to tighten the flare nut to prevent flare nut
cracking and leaks.
Not recommended, but in case of emergency
Should you be forced to connect the piping without a torque
wrench, follow the following installation method:
■
Tighten the flare nut using a spanner until the tightening
torque suddenly increases.
■
From that position further tighten the flare nut the angle listed
below:
Water piping work
Checking the water circuit
The units are equipped with a water inlet and water outlet for
connection to a water circuit. This circuit must be provided by a
licensed technician and must comply with all relevant European and
national regulations.
Before continuing the installation of the unit, check the following
points:
■
The maximum water pressure is 4 bar.
■
The maximum water temperature is 85°C.
■
Drain taps must be provided at all low points of the system to
permit complete drainage of the circuit during maintenance.
One drain valve in the indoor unit is provided to drain the water
from the indoor unit water system.
■
Make sure to provide a proper drain for the pressure relief valve
to avoid any water coming into contact with electrical parts.
■
Air vents must be provided at all high points of the system. The
vents should be located at points which are easily accessible for
servicing. An automatic air purge is provided inside the indoor
unit. Check that this air purge valve is not tightened too much so
that automatic release of air in the water circuit remains possible.
■
Take care that the components installed in the field piping can
withstand the water pressure and temperature.
■
Always use materials which are compatible with the water used
in the system and with the materials used on the indoor unit.
Checking the water volume and expansion vessel
pre-pressure
The unit is equipped with an expansion vessel of 12 litre which has a
default pre-pressure of 1 bar.
To assure proper operation of the unit, the pre-pressure of the
expansion vessel might need to be adjusted and the minimum and
maximum water volume must be checked.
1
Check that the total water volume in the installation, excluding
the internal water volume of the unit, is 20 l minimum.
Piping size
(mm)
Tightening
torque (N•m)
Flare dimensions A
(mm)
Flare shape
(mm)
Ø9.5
33~39
12.8~13.2
Ø15.9
63~75
19.4~19.7
Piping size
(mm)
Further tightening
angle (degrees)
Recommended arm
length of spanner (mm)
Ø9.5
60~90
±200
Ø15.9
30~60
±300
The unit is only to be used in a closed water system.
Application in an open water circuit can lead to excessive
corrosion of the water piping.
R=0.4~0.8
45
±
2
90
±
2
A
1
Piping union
2
Spanner
3
Flare nut
4
Torque wrench
4
2
3
1
WARNING
It is strongly recommended to install an additional filter on
the heating water circuit. Especially to remove metallic
particles from the field heating piping, it is advised to use a
magnetic or cyclone filter which can remove small
particles. Small particles can damage the unit and will not
be removed by the standard filter of the heat pump unit.
In most applications this minimum water volume will have a
satisfying result.
In critical processes or in rooms with a high heat load
though, extra water volume might be required.
When circulation in each space heating/radiator loop is
controlled by remotely controlled valves, it is important that
this minimum water volume of 20 l is kept even if all the
valves are closed.
Example
1
Outdoor unit
10
Radiator (field supply)
2
Indoor unit
11
Electronic expansion
valve
3
Refrigerant heat
exchanger
C1
Remote controller
4
Water heat exchanger
M1...M3
Individual motorized valve
to control loop radiators
(field supply)
5
Compressor
6
Pump
T1...T3
Individual room
thermostat (field supply)
7
Shut-off valve
8
Collector (field supply)
A
Installation space
9
By-pass valve
(field supply)
B
Living room
7 7 8
4
3
2
9
1
6
10
5
T3
T2
A
B
C1
M3
M2
M1
T1
11
11
4PW60970-1B_digital_EN.book Page 12 Thursday, September 2, 2010 1:15 PM
Содержание EKHBRD011ABV1
