background image

Operation manual

9

0 EKCBX/H008BAV3

Unit for air to water heat pump system

4PW64603-1A – 08.2010

Programming

Programming space heating or space cooling

Programming space heating or space cooling is carried out as
follows:

1

Use the 

=

 button to select the operation mode (cooling or

heating) you want to program.

2

Press the 

<

 button.

The actual mode is blinking.

3

Press the 

<

 button to con

fi

rm the selected mode.

The actual day is blinking.

4

Select the day you would like to consult or to program by means
of the 

pi

 and 

pj

 buttons.

The selected day is blinking.

5

Press the 

<

 button to con

fi

rm the selected day.

The 

fi

rst programmed action of the selected day appears.

6

Use the 

pi

 and 

pj

 buttons to consult the other

programmed actions of that day.

This is called the readout mode. Empty program actions (e.g. 4
and 5) are not displayed.

7

Press the 

<

 button for 5 seconds to enter the programming

mode.

8

Use the 

<

 button to select the action number you would like to

program or to modify.

9

Use the 

ba

 button to select:

-

x

: to switch cooling or heating and the controller off.

-

9

: set the temperature by means of the 

bi

 and 

bj

 buttons.

-

a

: to select automatic temperature calculation (only in 

heating mode).

10

Use the 

pi

 and 

pj

 buttons to set the correct action time.

11

Repeat steps 

8

 to 

10

 to program the other actions of the

selected day.

When all actions have been programmed, make sure that the
display shows the highest action number you would like to save.

12

Press the 

<

 button for 5 seconds to store the programmed

actions.

If the 

<

 button is pressed when action number 3 is displayed,

actions 1, 2 and 3 are stored but 4 and 5 are deleted.

You automatically return to step 

6

.

By pressing the 

pr

 button several times, you return to previous

steps in this procedure and 

fi

nally return to normal operation.

Programming space heating or space cooling are both
done in the same way. At the start of the programming
procedure space heating or space cooling is selected.
After that, you have to return to the start of the
programming procedure to program the other operation
mode.

5 sec

5 sec

Returning to previous steps in the programming procedure
without saving modi

fi

ed settings is done by pressing the

pr

 button.

Содержание EBHQ006BAV3





















Отзывы: