background image

2

REPLACEMENT PARTS

Ordering Parts

When reporting shortages or damages, or ordering repair 

parts, give the complete unit model and serial numbers as 

stamped on the unit’s nameplate. 

Replacement parts for this appliance are available through 

your contractor or local distributor. For the location of your 

nearest distributor, see website 

www.daikincomfort.com 

 

or contact:

EQUIPMENT SUPPORT

DAIKIN NORTH AMERICA LLC

19001 KERMIER ROAD

WALLER, TEXAS 77484

855-770-5678

SAFETY INSTRUCTIONS

 RECOGNIZE THIS SYMBOL AS A 

SAFETY PRECAUTION. 

These installation instructions  cover  the 

outdoor 

installation of single package heating and cooling units.  

See the Specification Sheet applicable to your model for 

information regarding accessories.

*NOTE:  Please contact your distributor or our 

website for the applicable Specification Sheet 

referred to in this manual.

To The Installer

Before installing this unit, please read this manual to 

familiarize  yourself on the specific items which must be 

adhered to, including maximum external static pressure to 

unit, air temperature rise, minimum or maximum CFM and 

motor speed connections. 

Keep this literature in a safe place for future reference.

CAUTION

Sheet metal parts, screws, clips and similar 

items inherently have sharp edges, and it 

is necessary that the installer and service 

personnel exercise caution.

WARNING

Do not connect to or use any device that is 

not design certified by daikin for use with this 

unit. Serious property damage, personal injury, 

reduced unit performance and/or hazardous 

conditions may result from the use of such non-

approved devices.

WARNING

To avoid property damage, personal injury 

or death, do not use this unit if any part has 

been under water. Immediately call a qualified 

service technician to inspect the furnace and to 

replace any part of the control system and any 

gas control having been under water. 

WARNING

This unit must not be used as a “construction 

heater” during the finishing phases of 

construction on a new structure. This type of 

use may result in premature failure of the unit 

due to extremely low return air temperature 

and exposure to corrosive or very dirty 

atmospheres. 

WARNING

HIGH VOLTAGE!

Disconnect all power before 

servicing or installing this unit. 

Multiple power sources may be 

present. Failure to do so may cause 

property damage, personal injury or 

death. 

WARNING

To prevent the risk of property damage, 

personal injury, or death, do not store 

combustible materials or use gasoline or other 

flammable liquids or vapors in the vicinity of 

this appliance. 

Содержание DP16H M Series

























Отзывы: