manualshive.com logo in svg

Daikin DCM601A72, Руководство по установке

Поделиться
Скачать
Daikin DCM601A72 Скачать руководство пользователя страница 32

32

Installation  Manual   3P291714-4

DCM601A72   iTM plus adaptor

English

6 

Quick Operation Guide

This chapter describes how to start/stop the areas and management points registered 
with the intelligent Touch Manager and display their information quickly. For detailed oper-
ation procedures, refer to the user’s manual.

6.1 

Viewing target area and management point information in 
list format

A

B

B

A 

Touch the List button.

B 

The screen changes to the list view, where the name, operation mode, set tempera-
ture, and fan speed of all areas and indoor units are listed.

6.2 

Viewing target areas and management points

A

B

A 

You can check the hierarchy level of the current area or indoor unit.

B 

Touch the Down button to go to the area being selected and view the areas and 
management points in it.

C

C 

Touch the Up button to go to the area one level above the current area.

01_EN_3P291714-4.indd   32

3/26/2012   5:00:49 PM

Содержание DCM601A72





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды