Daikin BRC230Z4, Руководство по установке

Страница: 15 / 16

1. Insert one end of P1/P2 harness into socket S9 located on the lower interface
PCB (A1P). Diagram 1.
2. Loosen (4) plastic nuts. Diagram 2.
3. Screw in (4) PCB post and gently tighten. Diagram 3
4. Install upper Interface PCB (A2P) in the same direction as lower Interface
PCB (A1P). Diagram 4.
5. Add (4) plastic nuts and gently tighten. Diagram 4.
6. Plug the loose end of P1/P2 harness into socket S7 of upper Interface PCB
(A2P). Diagram 4.
7. Wire Power harness into LN terminal block X3M (Black- L)
(White –N) (Green – Earth). Diagram 5.
8. Plug the other end of the power harness into S1 socket of the upper Interface
PCB (A2P). Diagram 5.
9. Pass the Remote controller cable through the 2 open cable ties. If the cable
ties have already been tightened cut the cable ties and use the spare cable
ties supplied to secure the controller leads. Diagram 7.
10. Plug the remote controller cable connector into socket S8 of upper Interface
PCB (A2P). Diagram 6.
11. Secure the earth shield to the earth shield post. Diagram 7.
TO REMOTE CONTROLLER
TO RELAY PCB S19 (8 ZONE ONLY)
TO RELAY PCB S19 (4 ZONE)
A2P A1P
L N E
S12
S7 S9
S2
S1 S1
S3
S13 S12 S13
S8
TN1
(NOTE 2)
TN2
S7 S9
S2 S3
S8
TO SUB CONTROLLER
TN1
TN2
TO P1 P2 TERMINAL
BLOCK (NOTE1)
B W G X3M
Sub Controller Instructions BRCSZC
S9
S9 S9
S9
S1
L N
S7
1 2 3 4 5 6
7
S9
S8
L N
ACCESSORIES
CABLE
TIE
X 5
SUB ZONE
KEYPAD
X 1
P1/P2
HARNESS
X 1
POWER
HARNESS
X 1
PCB
POST
X 4
INTERFACE
PCB X 1
15M
CONTROLLER
CABLE
X 1
Remote controller wiring
A N E
A N E
S7
MODE
FAN
TEMP
ADJUST
BUTTON
TEMP
SHIFT
7 DAY
TIME CLOCK
ON/OFF
TIMER
ENTER
CLEAR
TEST/EXIT DAY TIME ZONE1 ZONE2 ZONE3 ZONE4
SEL SENSOR FIX SENSOR ZONE5 ZONE6 ZONE7 ZONE8
MODE
FAN
TEMP
ADJUST
BUTTON
TEMP
SHIFT
7 DAY
TIME CLOCK
ON/OFF
TIMER
ENTER
CLEAR
TEST/EXIT DAY TIME ZONE1 ZONE2 ZONE3 ZONE4
SEL SENSOR FIX SENSOR ZONE5 ZONE6 ZONE7 ZONE8
4PDA0687
NOTE:
1. P1 P2 TERMINAL BLOCK
LOCATED IN THE ELECTRICAL
BOX OF INDOOR UNIT.
2. TN1, TN2 ONLY USE DAIKIN
REMOTE TEMPERATURE
SENSOR KRCSO1-1
3. :TERMINAL
:CONNECTOR
4. SYMBOLS SHOW AS FOLLOWS
B: BLACK
W: WHITE
G: GREEN
A1P INTERFACE PRINTED CIRCUIT BOARD
A2P INTERFACE PRINTED CIRCUIT BOARD
TN1 REMOTE SENSORS 1
TN2 REMOTE SENSORS 2
S1
S9-S7
S7
S8
CONNECTOR
230~240V
A1P 7 A2P COMMUNICATION
A1P INDOOR COMMUNICATION
REMOTE CONTROLLER
A1P
A2P
X3M
SCREW
X 2
MOUNTING
BRACKET
X 1
INSTALLATION
INSTRUCTION
X 1
1. Insert one end of P1/P2 harness into socket S9 located on the lower interface
PCB (A1P). Diagram 1.
2. Loosen (4) plastic nuts. Diagram 2.
3. Screw in (4) PCB post and gently tighten. Diagram 3 4. Install upper Interface PCB (A2P) in the same direction as lower Interface
PCB (A1P). Diagram 4.
5. Add (4) plastic nuts and gently tighten. Diagram 4.
6. Plug the loose end of P1/P2 harness into socket S7 of upper Interface PCB (A2P). Diagram 4.
7. Wire Power harness into LN terminal block X3M (Black- A)
(White –N) (Green – Earth). Diagram 5.
8. Plug the other end of the power harness into S1 socket of the upper Interface
PCB (A2P). Diagram 5. 9. Pass the Remote controller cable through the 2 open cable ties. If the cable
ties have already been tightened cut the cable ties and use the spare cable
ties supplied to secure the controller leads. Diagram 7.
10. Plug the remote controller cable connector into socket S8 of upper Interface PCB (A2P). Diagram 6.
11. Wire the controller lead earth shield cable to the earth shield post. Diagram 7.
TO REMOTE CONTROLLER TO RELAY PCB S19 (8 ZONE ONLY) TO RELAY PCB S19 (4 ZONE)
A2P A1P
L N E
S12
S7 S8
S2
S1 S1
S3
S13 S12 S13
S8
TN1 (NOTE 2)
TN2
S7 S8
S2 S3
S8
TO SUB CONTROLLER
TN1
TN2
TO P1 P2 TERMINAL
BLOCK (NOTE1)
B W G X3M
Sub Controller Instructions BRCSZC
S9 S9 S9
S9
S1
A N
S7
1 2 3 4 5 6
7
S9 S8
A N
ACCESSORIES
CABLE
TIE X 5
SUB ZONE KEYPAD
X 1
P1/P2
HARNESS
X 1
POWER
HARNESS X 1
PCB
POST
X 4
INTERFACE
PCB X 1
15M CONTROLLER
CABLE X 1
Remote controller wiring
A N E
A N E
S7
MODE
FAN
TEMP
ADJUS T BUT TON TEMP SHIFT
7 DA Y TIME CLOC K ON/OFF TIMER
ENTE R
CLEA R
TEST/EXI T DAY TIME ZONE1 ZONE2 ZONE3 ZONE 4 SEL SENSO R FIX SENSO R ZONE5 ZONE6 ZONE7 ZONE 8
MODE
FAN
TEMP ADJUS T BUT TON TEMP SHIFT
7 DA Y TIME CLOC K
ON/OFF TIME R ENTE R
CLEA R
TEST/EXI T DAY TIME ZONE1 ZONE2 ZONE3 ZONE 4 SEL SENSO R FIX SENSO R ZONE5 ZONE6 ZONE7 ZONE 8
4PDA0687
NOTE:
1. P1 P2 TERMINAL BLOCK LOCATED IN THE ELECTRICAL
BOX OF INDOOR UNIT.
2. TN1, TN2 ONLY USE DAIKIN REMOTE TEMPERATURE
SENSOR KRCSO1-1
3. :TERMINAL
:CONNECTOR
4. SYMBOLS SHOW AS FOLLOWS B: BLACK
W: WHITE
G: GREEN A1P INTERFACE PRINTED CIRCUIT BOARD
A2P INTERFACE PRINTED CIRCUIT BOARD TN1 REMOTE SENSORS 1
TN2 REMOTE SENSORS 2
S1 S9-S7
S7 S8
CONNECTOR
230~240V A1P 7 A2P COMMUNICATION
A1P INDOOR COMMUNICATION REMOTE CONTROLLER
A1P
A2P
X3M
SCREW
X 2
MOUNTING
BRACKET
INSTALLATION INSTRUCTIONS INST ALLA TION MANUAL ZONE CONTROLLER Air Conditioners MODELS BRC230Z4 BRC230Z8
BRC24Z4 BRC24Z8 BRCSZC PLEASE READ THESE INSTRUCTIONS CAREFULL YBEFORE I NST ALLA TION. KEEP THIS M ANUAL IN A HANDY PLACE FOR FUTURE RE FERENCE.