Daikin ARQ Скачать руководство пользователя страница 9

Страница: 9 / 44

www.DaikinApplied.com

IM 1083-3

Wall Openings, Louvers, and

VentiMatic Shutter

Self-Contained Floor Models ARQ and GRQ are typically

installed in front of a wall opening containing a properly sized

louver that is designed to let in outside air while preventing

water (such as rain) from getting past the louver and into

the unit itself. A weather-tight seal keeps unwanted air and

moisture from entering the occupied space. Refer to Figure 7

through Figure 23, for louver details.

Figure 7: Horizontal and vertical blade louvers, without

flange, (see Caution below for louver blade orientation and

drainage)

Vertical Blade Louver

Horizontal Blade Louver

Outside Air

Bird Screen On Side Toward Unit

Bottom

Bird Screen On Side Toward Unit

CAUTION

Locate Drain Lip at bottom of vertical louver to allow proper drain-

age. For horizontal louvers, the louver blades should face down for

proper drainage. Bird screen should always be on side toward unit.

Figure 8: Horizontal and vertical blade louvers, without

flanges with grille or with flange without grille

Louver drain lip

Grille/Louver with weep hole

Flange

Outside Air

Vertical Louver with Flange, without Grille

Horizontal Louver

without Flange,

with Grille

Rear of Horizontal Blade Louver with Birdscreens and Flange

VentiMatic™ Shutter Assembly

In many installations, a Daikin Applied VentiMatic Shutter

Assembly is specified. See Figure 9. This one-way shutter is a

continuously variable, gravity actuated, room exhaust vent that

operates in direct response to positive static pressure. It opposes

any airflow into the room and allows a slight positive pressure.

It is important that the VentiMatic shutter and unit ventilator

louvers are mounted on the same wall. This neutralizes the

effect of the wind. Forcing excess air into the room through the

unit ventilator louver overcomes the same wind pressure that

works to keep the VentiMatic shutter closed. This prevents room

air exhausting from the room through the VentiMatic shutter.

Figure 9: VentiMatic Shutter assembly

Note: Birdscreen and louver are shipped in one (1) piece.

Outside

Louver

VentiMatic Shutter

Roomside

Relief Air

Содержание ARQ













































Результаты поиска

Содержание ARQ

Отзывы:

Похожие инструкции для ARQ

Бренды по названию

Популярные бренды

Daikin ARQ, Руководство по установке и обслуживанию

Результаты поиска

Содержание ARQ

Отзывы:

Похожие инструкции для ARQ

Бренды по названию

Популярные бренды