background image

31

Setting the Vacation Timer

The vacation timer lets you set the date and time of your RETURN from vacation. Until that date/time, the system will remain at 

the VACATION heating and cooling setpoints specified in the configuration menu.
To use the EASY VACATION feature:

Press 

, then press the 

 to scroll to “Vacation” then press 

 again. The thermostat will automatically go into Vacation 

mode with the default return date 1 month later .

To set the vacation timer (and begin vacation setpoint mode): 

1.

 Press 

 to select operating mode. 

 

2.

 Press 

, then press 

 until VACATION appears. 

3.

Press 

 to enter date and time you plan to RETURN from vacation.

4.

 When your finished entering the date/time, press 

.

Schedule Override

The schedule override feature allows the user to override the program schedule for 1 to 5 hours. In addition, if selected, the 

schedule can be overridden only until the next transition period.

To access the Schedule override feature, enter the 

 screen, then use 

 to scroll through the menu options until you reach 

the SCHEDULE OVERRIDE screen. In the default setting, the Vacation & Schedule periods will be flashing in the upper right 

corner of the LCD. In this mode, the Vacation & Schedule will be overridden until the next transition period. To switch to the 1-5 

hour override, use the 

 arrow. This mode allows the user to override the Schedule set points for 1-5 hours.

Alarm Reset

This thermostat is equipped with unit fault reset capabilities when used with the Michrotech III WSHP unit controller.

If the water source heat pump enters a fault mode, the alarm icon will illuminate on the thermostat.  When the condition has 

been corrected, the unit can be reset from the thermostat.

1. Press the  

2. press the CONFIG  

 repeatedly until the alarm reset appears

3. Press the 

 arrow to change the display to Y, then press 

Содержание 910193130





































Отзывы: