6-15
Chapter 6
W
elding Condition
S
ETTING
W
ELDING
C
ONDITIONS
W
ELDING
C
ONDITION
C
HAPTER
6
<Relationship of wire diameter and welding current at aluminum welding (Reference)>
*1: Note that the "collective" voltage adjustment may not meet the appropriate condition if a mixing gas other than those
with the following mixing ratios is used.
*1-1: MAG gas: Argon (Ar) 80 % + Carbon dioxide (CO
2
)20 %
*1-2: MAG gas: Argon (Ar) 90 % + Carbon dioxide (CO
2
)10 %
*1-3: MIG gas (stainless steel): Argon(Ar) 98 % + Oxygen (O
2
)2 %
*1-4: MIG gas: Argon(Ar)97.5 % + Carbon oxygen (CO
2
)2.5 %
*1-5: MIG gas (Aluminum/Aluminum bronze/Silicon bronze): Argon (Ar)100 %
*2: Available for applications either of "STANDARD" or "HIGH".
*3: For "STANDARD" mode, the standard mode or extended cable mode (extended mode of power cable) is available.
(
-
F1: Standard/Extended cable mode)
*4: In the welding of DC low spattering, the following devices are necessary for wire feeder and welding torch. For details,
refer to the instruction manual of each device.
• Wire feeder: CMV-7402
• Welding torch: WT3500V-SD or WT3510V-SD
Aluminum material
Wire diameter
(mm
Φ
)
Welding method
Range of stable welding
power source (A)
HARD ALUMINUM
(A5183, A5336 etc.)
1.0
DC
60 to 150
DC pulse/DC wave pulse
50 to 150
1.2
DC
75 to 250
DC pulse/DC wave pulse
50 to 250
1.6
DC
100 to 350
DC pulse/DC wave pulse
75 to 350
SOFT ALUMINUM
(A4043 etc.)
1.2
DC
90 to 250
DC pulse/DC wave pulse
60 to 300
1.6
DC
100 to 350
DC pulse/DC wave pulse
75 to 350
0.8
OP
0.9
1.0
1.2
1.6
1.4
F
A
m/min.
V
r
A
V
r
㧑
Al/PURE
OP3
Al/Mg
INCONEL
TITANIUM
OP2
OP1
DC STICK
DC TIG
WELDING
METHOD
CO
2
OP
MAG
MIG
MIG
GAS
㧔
2.5%CO
2
㧕
㧔
100%Ar
㧕
Hz
WARNING
sec.
m/min.
JOB No.
DISPLAY
CHANGE
PRE
FLOW
POST
FLOW
MAIN
CONDITION
INITIAL
CONDITION
CRATER-FILL
CONDITION
ARC
CONTROL
INITIAL
CONDI
-TION
ON
CONSTANT PENETRATION
ON
WELD
MONITOR
WATER
TORCH
SYNERG.
INDIV.
SYNERG.
VOLT.ADJUST
㧔
3 sec.
㧕
GAS
WIRE INCH
SPOT TIME
OFF
ON
SPOT
CRATER
-FILL
WIRE DIA.
(mm)
MILD STEEL
MILD STEEL
CORED
STAINLESS
STEEL
STAINLESS
CORED
Brazing Cu Sl
DC PULSE
DC
DC WAVE PULSE
STANDARD
OP2
HIGH
OP1
TRAVEL
SPEED
LOAD
SAVE
ENTER
WIRE
MATERIALS
STAINLESS
FERRITE
DC LOW SPATTER
(P500L ONLY)
OP
WAVE FRQ
ON
Brazing Cu Al
20%CO
2
㧕
㧔
MAG 10%CO
2
㧕
㧔
MIG
㧔
2%O
2
㧕
WIRE DIA. (mm) key
WIRE MATERIALS key
GAS key
TRAVEL SPEED key
WELDING METHOD key
CONSTANT PENETRATION key
Содержание OTC Welbee P500L
Страница 2: ......
Страница 8: ...TABLE OF CONTENTS vi MEMO...
Страница 142: ...TROUBLESHOOTING TROUBLESHOOTING CHAPTER 9 9 6...
Страница 158: ...MATERIALS FOR SETTING WELDING CONDITIONS REFERENCE MATERIALS CHAPTER 10 10 16...