Dahua SD60-***-SL Series Скачать руководство пользователя страница 9

Страница: 9 / 42

Installation Preparation

1.1

Basic requirements



All installation and operation here should conform to your local electrical safety codes.



Before installation, please open the package and check all the components are included.



Please make sure the speed dome installation environment and installation mode can meet

your requirement. If there is special requirement, please contact your local retailer for more

information.



We assume no liability or responsibility for all the fires or electrical shock caused by

improper handling or installation.

1.2

Installation Check



Please make sure the installation environment has enough space to install the speed dome

and its corresponding bracket.



Please make sure the ceiling, wall and the bracket can sustain the 8X weight of the speed

dome and its installation components.



Please make sure the wall is thick enough to install expansion bolts (need to be purchased).



Please notice that the installation height should be more than 6m if it is a laser speed dome.

1.3

Cable Requirements

1.3.1 Video Cable Requirements

The minimum video cable requirements are as follows:



75 ohm impedance.



Full copper core cable.



95% knitted copper shield

Different types of devices use different cable models. Please refer to sheet 1-1 for the cable used

by analog and network speed dome, please refer to sheet 1-2 for the cable used by HDCVI

speed dome.

International Model

Max Distance
(Ft\M)

RG59/U

750ft (229m)

RG6/U

1,000ft (305m)

RG11/U

1,500ft (457m)

Sheet 1-1

International Model

Max Distance
(Ft\M)

SYV-75-3

720P

（

25fps\30fps

）：

1640ft\500m

720P

（

50fps\60fps

）：

984ft\300m

1080P

（

25fps\30fps

）：

984ft\300m

Sheet 1-2

Содержание SD60-***-SL Series











































Результаты поиска

Содержание SD60-***-SL Series

Отзывы:

Похожие инструкции для SD60-***-SL Series

Бренды по названию

Популярные бренды

Dahua SD60-***-SL Series, Руководство по установке

Результаты поиска

Содержание SD60-***-SL Series

Отзывы:

Похожие инструкции для SD60-***-SL Series

Бренды по названию

Популярные бренды