background image

1. 

Important Safeguards and Warnings 

Please read the following safeguards and warnings carefully before using the product in 

order to avoid damages and losses. 

Note: 

 

Do not expose the device to lampblack, steam or dust. Otherwise it may cause 

fire or electric shock.   

 

Do not install the device at position exposed to sunlight or in high temperature. 

Temperature rise in device may cause fire. 

 

Do not expose the device to humid environment. Otherwise it may cause fire.   

 

The  device  must  be  installed  on  solid  and  flat  surface  in  order  to  guarantee 

safety under load and earthquake. Otherwise, it may cause device to fall off or 

turnover. 

 

Do not place the device on carpet or quilt. 

 

Do not block air vent of the device or ventilation around the device. Otherwise, 

temperature in device will rise and may cause fire. 

 

Do not place any object on the device.   

 

Do not disassemble the device without professional instruction. 

 

 

Warning:

 

 

Please use battery properly to avoid fire, explosion and other dangers.   

 

Please replace used battery with battery of the same type.   

 

Do  not  use  power  line  other  than  the  one  specified.  Please  use  it  properly. 

Otherwise, it may cause fire or electric shock.     

 

Special Announcement 

 

This manual is for reference only.   

 

All  the  designs  and  software  here  are  subject  to  change  without  prior  written 

notice.   

 

owners.   

 

If there is any uncertainty or controversy, please refer to the final explanation of 

us.   

 

 

Поставщик систем безопасности TELECAMERA.RU

Содержание ARD1611-W













Отзывы: