Dahua Technology Digital signage LDV43-SAI200 Скачать руководство пользователя

Страница: 5 / 38

Regulatory Information

Regulatory Information

The regulatory information herein might vary according to the model you purchased. Some

information is only applicable for the country or region where the product is sold.

FCC Information

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

FCC conditions:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:



This device may not cause harmful interference.



This device must accept any interference received, including interference that may

cause undesired operation.

FCC compliance:

This equipment has been tested and found to comply with the limits for a digital device,

pursuant to part 15 of the FCC Rules. This equipment generate, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the guide, may cause

harmful interference to radio communication.



For class A device, these limits are designed to provide reasonable protection against

harmful interference in a commercial environment. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.



For class B device, these limits are designed to provide reasonable protection against

harmful interference in a residential installation. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.



Consult the dealer or an experienced radio/TV technician for help.

Содержание Digital signage LDV43-SAI200







































Результаты поиска

Содержание Digital signage LDV43-SAI200

Отзывы:

Похожие инструкции для Digital signage LDV43-SAI200

Бренды по названию

Популярные бренды

Dahua Technology Digital signage LDV43-SAI200, Руководство пользователя

Результаты поиска

Содержание Digital signage LDV43-SAI200

Отзывы:

Похожие инструкции для Digital signage LDV43-SAI200

Бренды по названию

Популярные бренды