background image

 
 
 

TURNING ON YOUR SHREDDER 

 

  ON, OFF and REVERSE are controlled by the black 

     Rocker Switch (3) on the top of the shredder. 

  Moving the switch to the “I” (ON) position 

     places the shredder in the standby mode. 
 

Note: Shredder will run momentarily

  Moving the switch to the center or “O” (OFF) 

     position turns the shredder off. 

  The REVERSE position “R” will be discussed 

     in “CLEARING A PAPER JAM”. 

 
 
SHREDDING 

 

 

Turn shredder on.  Insert paper squarely into 
Feed Opening (1).  A light barrier (2) will auto- 
matically activate the shredding mechanism. 
Continue feeding paper into the Feed Opening 
until the shredding mechanism begins to 
draw the paper in.  At this point, allow the paper 
to feed into the shredder on its own.  Once the 
paper has passed completely through the shredding mechanism, the electronic 
controls will automatically stop the machine. 
 
 
Microfiche and transparencies can also be shredded in the same manner as 
paper, however, you should shred a piece of paper after every 8 or 10 sheets of 
plastic.  This helps clean plastic particles out of the shredding mechanism. 
 
 
 
 
 
 
 
 
 
 
 

 
CAPACITY 

 
Capacity is the number of sheets of 8½” x 11” paper that can be shredded at 
one time.  These figures are approximate and machines may vary slightly due to 
various conditions.  It is not recommended that you try to run your shredder at 
maximum capacity, as this increases the chance of a paper jam. 
 
 

Model   

20 Lb. Bond   

16 Lb. Bond 

 

20404 

16   20 

 20414 

12 

15 

 20422 

10 

12 

 

20430 

  5 

  6 

 

20434 

  4 

  6 

 20506 

25 

30 

 20514 

12 

15 

 

 

 

 

 

CLEARING A PAPER JAM 

 
 
If too many sheets of paper are fed into your shredder at one time, it may cause 
a paper jam.  Running your shredder at maximum capacity increases the 
chance of a paper jam.  If a paper jam occurs, it is easy to clear by following 
these simple steps: 
 

Turn shredder off using ON/OFF/REVERSE switch (3) 

 Firmly pull on paper sticking out of Feed Opening while holding 

   ON/OFF/REVERSE switch in the REVERSE (R) position. 

 After paper has been removed from the Feed Opening, move 

    the ON/OFF/REVERSE switch back to the ON (I) position. 

 Separate some of the sheets and continue shredding. 

 

 

ALWAYS TURN SHREDDER OFF IF IT WILL BE UNATTENDED FOR LONG PERIODS OF TIME

IT IS NOT RECOMMENDED RUNNING SHREDDERS AT MAXIMUM CAPACITY 

abcoffice

www.abcoffice.com                 (800) 658-8788

Содержание 20400 Series

Страница 1: ...20400 SERIES INTERMEDIATE OFFICE SHREDDERS 20404 20414 20422 20430 20434 20500 SERIES ECONOMY OFFICE SHREDDERS 20506 20514 OPERATION MANUAL 20404 90 0830 03 04 abcoffice www abcoffice com 800 658 8788 ...

Страница 2: ...ing LED indicator Bag full Door ajar 5 Power Light 6 Transport Bolts 7 Waste Bin 8 Shred Bag 9 Door Pull 10 Door BEFORE YOU CALL FOR SERVICE SYMPTOM POSSIBLE CAUSES SOLUTION No Power ON OFF Switch set to Move Switch to I on wrong position position Unit unplugged Connect to outlet Outlet dead Reset circuit breaker Door not fully closed Close Door Shred Bag full Change Shred Bag Low capacity Cutting...

Страница 3: ...te the lubricant evenly You can now continue shredding as usual DAHLE Shredder Oil is the only lubricant you should use in your paper shredder It has been specially formulated so as not to leave any residue that could attract dust and clog the shredding mechanism You can order DAHLE Shredder Oil item 740 from your local dealer Repairs on your paper shredder should only be performed by qualified te...

Страница 4: ...es out of the shredding mechanism CAPACITY Capacity is the number of sheets of 8 x 11 paper that can be shredded at one time These figures are approximate and machines may vary slightly due to various conditions It is not recommended that you try to run your shredder at maximum capacity as this increases the chance of a paper jam Model 20 Lb Bond 16 Lb Bond 20404 16 20 20414 12 15 20422 10 12 2043...

Отзывы: