Dahl VARIODOCK Скачать руководство пользователя страница 12

22

23

2

1

Maintenance manual, installation and user guide UK

Dahl VarioDock™

Po

tentiome

ter

Mo

tor (+)

Solenoid /

Electromagnet (+)
Solenoid /

Electromagnet (-)

+12V battery

-battery

Reset-button

Mo

tor (-)

Micr

oswit

ch

Parking 

brake

Display

DIP swit

ch

DIP switch

Electrical connection

Settings on DIP switches

 

 DIP 1 og DIP 2:

  

 

 

Setting the tightening rate by pressing the blue button on the control panel

 

If VarioDock is to be used for multiple wheelchairs, we recommend choosing a low 

tightening rate to avoid any damage to the wheelchairs due to excessive pulling. 

  

! NOTE:

 Please enquire from the wheelchair manufacturer whether the wheelchair 

may be pulled down, in order to avoid damage to the wheelchair. 

DIP 1

DIP 2

Tightening rate

OFF

OFF

15 kg +/- 10

OFF

ON

30 kg +/- 10

ON

OFF

40 kg +/- 10

ON

ON

50 kg +/- 10

 

DIP 3:

 Holding time of the lock pin

DIP 3

Holding time of the lock pin

OFF

5 seconds

ON

8 seconds

 

 

DIP 4:

 Activation of parking brake

DIP 4

Parking brake contact function: NO or NC

OFF

If a signal is connected when the parking brake is being activated, so that 

12V can be measured on the control unit’s parking brake terminals 1 and 

2 (polarity is irrelevant), switch 4 on DIP switch must be set to OFF (NO 

function).

ON

If a signal is cut off when the parking brake is activated, so that 12 V 

CANNOT be measured on the control module’s parking brake terminals 1 

and 2 (polarity is irrelevant), switch 4 on DIP switch must be set to ON (NC 

function).

 

1.

  Disconnect the cable on the battery’s negative terminal. 

2.

   Find a suitable installation site for the control panel. 

 

 If the docking station is used by a person driving the vehicle himself 

– At an easily accessible and visible location when the wheelchair is 

secured in the docking station and the driver is looking forward from 

the driving position. 

 

 If the docking station is for a passenger

 – At a location which is visible 

when the driver of the vehicle is sitting in the driver’s seat and looking 

forward. 

3.

   Wiring must be installed so that it is not exposed to mechanical loads 

such as wear, vibrations, kinks and sharp edges which can cause breaks 

and result in malfunctions or, in the worst case, a short circuit.

 

 To ensure sufficient power supply to the docking station, the supply 

cable must be installed directly to the vehicle’s battery, otherwise there 

is a risk of malfunction and overload of the vehicle’s original wiring. 

The power supply must be fused with a 30 amp fuse (not included.) See 

the wiring diagram on page 24 for correct connection. 

4.  Electrical connection 

 

 -  To reset the maintenance counter, press the reset button down on the 

circuit board for approx. 15 seconds. The yellow LED on the control 

panel flashes when the reset is done.

 

- Parking brake (1) and (2): Polarity is not important.

 

-  The software reset is performed by pressing the up and down buttons 

of the control panel simultaneously for 3 seconds.

 

-  Function when lock pin is blocked: To protect the electrical system 

from overload, the power supply for the locking mechanism will 

pulsate if blocking the lock pin. This can be can be heard as pulsating/

clicking sound from inside the docking station.

 

DIP 5:  

Display which shows ground clearance (see Fig. I on page 15) can be set 

to be permanently active or switch off after 30 seconds.

DIP 5

Display state

OFF

Display will switch off after 30 seconds

ON

Display is permanently active 

 

DIP 6:

 No function

 

DIP 7 og DIP 8:

 Calibration of the height

  

Prior to calibration, it must be ensured that VarioDock can be adjusted with-

in the full range of travel (61-91mm)! Settings MUST be made in the order 

shown.

DIP 7

DIP 8

Function

 

OFF

OFF

1. Adjust VarioDock™ to approx. middle of the full range 

of travel

ON

OFF

2. Adjust the VarioDock™ to the top position – wait until 

it stops by itself, before releasing the button

ON

OFF

3. Adjust the VarioDock™ to the bottom position - wait 

until it stops by itself, before releasing the button

ON

ON

4. Set the display to lowest position in millimetres 

(61mm) with the up / down buttons

ON

OFF

5. Adjust the VarioDock™ to the top position - wait until 

it stops by itself, before releasing the button

ON

ON

6. Set the display to highest position in millimetres 

(91mm) with the up / down buttons

OFF

OFF

7. The settings are complete

5.  

Carefully fit the docking station’s top. It is important that the potentiometer 

pin be placed in the hole in the bottom frame when assembling slides and 

bottom frames. Otherwise there is a risk of damaging the potentiometer. If the 

docking station's top is fitted and the potentionmeter is not sitting properly in 

the hole, it will be damaged. See instructions on page 17. Please be careful to 

place wires and cables so that they do not touch the moving parts.

6.  Fit the cable onto the battery’s negative terminal.

Содержание VARIODOCK




















Отзывы: