DAF CF65 Скачать руководство пользователя | Manualshive

Страница: 242 / 504

background image

3

ZF 8/16S-151/181 AND 16S-221 GEARBOXES

Removal and installation of gearbox

CF

65/75/85

series

4-4

4.2 REMOVAL AND INSTALLATION, PROP SHAFT FLANGE

Removing prop shaft flange

1.

Remove the prop shaft from the gearbox
flange and hang it on the chassis.

2.

Hold the prop shaft flange in place with the
special tool (DAF No. 0484977).

3.

Remove the attachment bolts from the prop
shaft flange.

4.

Remove the bolts and locking plate from the
prop shaft flange.

5.

Note:

Measure and make a note of the distance
from the prop shaft flange to the shaft. The
same distance must be observed when the
prop shaft flange is reinstalled.

Remove the prop shaft flange and O-ring
using a commercially available puller.

Fitting prop shaft flange

1.

Lightly oil the oil seal in the bearing cover.

2.

Heat the prop shaft flange to 70

_

C. Slide it

as far as possible onto the output shaft. Use
the locking plate and two standard bolts
(M12x75) to pull the prop shaft flange
further onto the shaft.

3.

Remove the standard bolts and measure
whether the prop shaft flange has reached
the correct position on the output shaft.

4.

Fit a new O-ring into the recess between
the output shaft and the prop shaft flange.

V300449

7

ᓻ

200337

https://www.truck-manuals.net/

«
...
240
241
242
243
244
...
»

Содержание CF65

























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CF65

Бренд: U-Line Страницы: 6

Бренд: jcb Страницы: 31

Magliner H-4938

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 25

swaploader SL-105

Бренд: Efco Страницы: 82

WorkStar Series

Бренд: Navistar Страницы: 258

Бренд: Tractel Group Страницы: 20

Бренд: Tractel Страницы: 17

Бренд: U-Line Страницы: 4

Бренд: Movexx Страницы: 61

Бренд: Ford Страницы: 37

F-150 RAPTOR 2018

Бренд: Ford Страницы: 55

Бренд: Ford Страницы: 110

Бренд: Taylor-Dunn Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды