background image

11

INSTALLATION

1. Steady, flat location.

This microwave oven should be set on a steady, flat surface.

2. Leave space behind and side.

All air vents should be kept a clearance. If all vents are covered during operation, the oven may be overheated
and, eventually, cause oven failure.

3. Away from radio, and TV sets

Poor television reception and radio interference may result if the oven is located close to a TV, radio, antenna, or
feeder and so on.

4. Away from heating appliances and water taps

Keep the oven away from hot air, steam or splash when choosing a place to position it, or the insulation might be
adversely affected and breakdowns occur.

5. Power supply

  Check your local power source.

This microwave oven requires a current of approximately 12 amperes, 230 Volts, 50 Hz.
Power supply cord is about 1 meters long.

 The voltage used must be the same as specified on this oven. Using a higher voltage may result in a fire or other

accident causing oven damage. Using low voltage will cause slow cooking. We are not responsible for damage
resulting from use of this oven with a voltage of ampere fuse other than those specified.

 This appliance is supplied with cable of special type, which, if damaged, must be repaired with cable of same

type.
Such a cable can be purchased from DAEWOO and must be installed by a qualified person.

6. Examine the oven after unpacking for any damage such as:

A misaligned door, broken door or a dent in cavity.
If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.

7. Do not operate the oven if it is colder than room temperature

(This may occur during delivery in cold weather.) Allow the oven to become room temperature before operating.

EARTHING INSTRUCTIONS

This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of the electric
shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a earth-
ing plug. The plug must be plugged into an outlet that is properly installed and earthed.

WARNING

Improper use of the earthing plug can result in a risk of electric shock. Consult a qualified electrician or service-
man if the earthing instructions are not completely understood, or if doubt exists as to whether the appliance is
properly earthed, and either : If it is necessary to use an extension cord, use only a 3-wire extension cord that
has a 3-blade earthing plut, and a 3-slot receptacle that will accept the plug on the appliance. The marked rating
of the extension cord should be equal to or greater than the electrical rating of the appliance, or Do not use an
extension cord.

Содержание KOR-41151S









































Отзывы: