background image

25

1. High voltage is present at the high voltage terminal of the high voltage transformer during any cook cycle.
2. It is neither necessary nor advisable to attempt measurement of the high voltage.
3. Before touching any oven components or wiring, always unplug the oven from its power source and discharge the

capacitor (see page 8).

1. High voltage transformer

(A) Remove connections from the transformer terminals and

check continuity.

(B) Normal readings should be as follows:

Secondary winding

Approx. 90

± 10%

Filament winding

Approx. 0

Primary winding

Approx. 0

2. High voltage capacitor

A) Check continuity of capacitor with meter on the highest

ohm scale.

(B) A normal capacitor will show continuity for a short time,

and then indicate 9M

once the capacitor is charged.

(C) A shorted capacitor will show continuous continuity.
(D) An open capacitor will show constant 9M

.

(E) Resistance between each terminal and chassis should

be infinite.

3. High voltage diode

The high voltage diode is located on the base near the
transformer.

(A) Isolate the diode from the circuit  by disconnecting the

leads.

(B) With the ohmmeter set on the highest resistance scale,

measure the resistance across the diode terminals.
Reverse the meter leads and again observe the
resistance reading. Meter with 6V, 9V or higher voltage
batteries should be used to check the front-to-back
resistance may be read in both directions. A normal
diodes resistance will be infinite in one direction and
several hundred K

in the other direction.

4. Magnetron

For complete magnetron diagnosis, refer to "Measure-
ment of the Microwave Output Power".
Continuity checks can only indicate and open filament or
a shorted magnetron. To diagnose for an open filament
or shorted magnetron.

(A) Isolate magnetron from the circuit by disconnecting the

leads.

(B) A continuity check across magnetron filament terminals

should indicate one ohm or less.

(C) A continuity check between each filament terminal and

magnetron case should read open.

COMPONENT TEST PROCEDURE

Secondary

terminal

Primary 

terminal

Filament terminal

Magnetron
antenna

Magnetron
chassis
ground

Metallic
gasket
plate

Cooling fin

Filament
terminal

Содержание KOG-875T2S









































Отзывы: