Daewoo KOC-970T1S Скачать руководство пользователя страница 24

Страница: 24 / 48

TROUBLE SHOOTING GUIDE

(TROUBLE 6) The following visual conditions indicate a probable defective touch control circuit or button P.C.B. assembly.

1. Incomplete segments

(1) Segments missing

(2) Partial segments missing

(3) Digit flickering other than normal fluorescent slight flickering

(4) 0 does not display when power is on.

2. A distinct change in the brightness of one or

more numbers exists in the display.

3. One or more digits in the display are not on

when they should be.

4. Display indicates a number different from one touched.

(for example, even if one touched 5, 3 appears in the display.

5. Specific numbers (for example, 2 or 3) do not display

when the button is touched.

6. Display does not count down or up with time cooking or

clock operation.

7. Oven is programable and cooks normally but no display shows.

8. Display obviously jumps in time while counting down.

9. Display counts down noticeably too fast while cooking.

10. Display does not show the time of day when clear button is touched.

11. Oven lamp and turntable motor do not stop although cooking is finished.

Check if the RELAY (RY3) contacts close and if they are close, replace touch control circuit.

CO N DITIO N

CHECK

RESULT

CAUSE

REM EDY

D isplay does

not show

program m ing
at all, even if

keyboard is

touched.

N orm al

R eplace

control box

sub-a ssem bly

R eplace

the button

keyboard

M alfunction

of touch

control circuit
of control box

sub-a ssem bly

N orm al

C heck eac h button for

continuity of the button

keyboard for the

following k eyboard

check procedure

M alfunction

of botton

keyboard

B efore follow ing the particular steps listed above in the trouble shooting guide for the button keyboard’s failure,
please check for the continuity of each w ire-harness betw een the button keyboard and P.C .B . assem bly.

NOTE

Содержание KOC-970T1S

















































Результаты поиска

Содержание KOC-970T1S

Отзывы:

Похожие инструкции для KOC-970T1S

Бренды по названию

Популярные бренды

Daewoo KOC-970T1S, Руководство по обслуживанию

Результаты поиска

Содержание KOC-970T1S

Отзывы:

Похожие инструкции для KOC-970T1S

Бренды по названию

Популярные бренды