Daewoo KOC-970T1S Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 48

background image

DISASSEMBLY AND ASSEMBLY

10. To remove motor syncro and under heater

(1) Cut the syncro motor cover parts from the base plate.

(2) Remove two screws which secure the motor syncro and supporter to bracket syncro motor.

(3) Remove two screws and under heater assembly in cavity

11. To remove grill heater assembly

(1)

Remove two screws which secure the cover insulator *t to top plate.

(2) Remove the harness between heaters.

(3) Remove two screws for removing heater brackets.

(4) Remove heaters.

(5) Reverse the above steps for reassembly.

«
...
15
16
17
18
19
...
»

Содержание KOC-970T1S

















































Отзывы:

Нет отзывов

Похожие инструкции для KOC-970T1S

SelfCooking Center

Бренд: Rational Страницы: 84

Trivection JT930

Бренд: GE Страницы: 48

TRIVECTION ZET3038

Бренд: GE Страницы: 2

Бренд: GE Страницы: 24

Profile Advantium SCB2000F

Бренд: GE Страницы: 40

Бренд: DeLonghi Страницы: 52

Бренд: Omega Страницы: 26

Бренд: Moffat Страницы: 1

Бренд: Teka Страницы: 72

Бренд: Ariston Страницы: 42

Бренд: Russell Hobbs Страницы: 22

Бренд: Premium Страницы: 21

508GG5.33HZpMsNAiQ

Бренд: Amica Страницы: 68

Бренд: Blodgett Страницы: 2

Бренд: Magic Chef Страницы: 32

Бренд: Rangemaster Страницы: 20

Бренд: Prima Страницы: 9

Бренд: Jocel Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды