Daewoo FPN-X22D3 Series Скачать руководство пользователя страница 16

Страница: 16 / 65

1. How to enter this check mode

1) Push the LOCK button.

2) Push the WATER button 5 times while pressing the FRZ.SET button.

2. The Front LED displays the current error code ( if happens ).

; Every time you press the Freezer Set button, the following value display.

1) The appliance running time. ( From the plug in. )

2) Freezer sensor temperature.

3) Defrost sensor temperature.

4) Refrigerator sensor temperature.

5) Room temperature.

6) P Factor display.

7) Filter remaing time until exchange. ( Initial filter runing time is about 4,320 Hour = 6 months )

3. How to exit this mode

1) Push the LOCK button.

Error Display ( Dispenser Models )

2) After 4 minutes automatically exit.

4. Error Code

Return after defrosting : abnormal or defective

Pull-Down mode display (No error)

Forced Defrost mode display (No error)

Drop the ice while Et

Full ice switch error

Abnormal or defective cycle

Flow sensor is defective.

Horizontal switch error

Water supply error

Freezer Door switch is defective.

Home Bar Door switch is defective.

Ice sensor disconnection or short

Room temperature sensor disconnection or short

Defrost sensor disconnection or short

Refrigerator Door switch is defective.

Display (Error Code)

Remark

Freezer sensor disconnection or short

Refrigerator sensor disconnection or short

; All Error Code reset, when the relative parts turn into normal.

Содержание FPN-X22D3 Series


































































Результаты поиска

Содержание FPN-X22D3 Series

Отзывы:

Похожие инструкции для FPN-X22D3 Series

Бренды по названию

Популярные бренды

Daewoo FPN-X22D3 Series, Руководство по обслуживанию

Результаты поиска

Содержание FPN-X22D3 Series

Отзывы:

Похожие инструкции для FPN-X22D3 Series

Бренды по названию

Популярные бренды