Daewoo FPN-X22D3 Series Скачать руководство пользователя страница 12

Страница: 12 / 65

3. Fan voltage per control mode

Exerted fan motor voltage

1) Normal control : Slow operation mode with relatively low noise level.

2) Load mode : Operation mode which need to be operated by temperature rise at inner side of

refrigerator according to operating condition.

4. Load mode

1) Purpose : To recover temperature rise inside of refrigerator as quickly as possible by load or frequent door opening.

FUNCTIONS ( Fan Control )

13 V

Load mode /

4 hours after defrosting

RT >= 38C

Mode

F-Fan

C-Fan

Super Freezer mode

13 V

Normal mode

10 V

13 V

2) Operating condition

- When door opening time is more than 1 minutes per 1 time -> Frz. / Ref. go to load mode.

- When sensing more than R/S On Point + 5deg : Ref. load response.

- When sensing more than F/S On Point + 5deg : Frz. load response.

3) Conditions for inactive load response mode.

- When there is no door opening signal during and after defrost cycle, load response mode is inactive.

4) Terminate condition

- After 20 mintues.

- When Ref. sensor reaches to off point, Ref. load mode ends.

- When Frz. sensor reaches to off point, Frz. load mode ends.

Содержание FPN-X22D3 Series


































































Результаты поиска

Содержание FPN-X22D3 Series

Отзывы:

Похожие инструкции для FPN-X22D3 Series

Бренды по названию

Популярные бренды

Daewoo FPN-X22D3 Series, Руководство по обслуживанию

Результаты поиска

Содержание FPN-X22D3 Series

Отзывы:

Похожие инструкции для FPN-X22D3 Series

Бренды по названию

Популярные бренды