11
Installation
10
Various methods in connecting with TV
AUDIO
VIDEO
S-VIDEO
ANT INPUT
S-VIDEO INPUT
A/V INPUT
COMPONENT INPUT
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PRESONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
20
18
16
14
12
10
8
6
4
3
21
19
17
15
13
11
9
7
5
3
1
R
ANT.IN
RF OUT
L
OUT
IN
AUDIO
VIDEO
R
COAXIAL
S-VIDEO OUT
L
Y
Pr
Pb
DIGITAL AUDIO OUT
COMPONENT OUT
AUDIO OUT
Method
Method
1
1
Remove circular cable (RF cable) (surplus cable) plugged in “ANT.IN” Jack in rear panel of TV. Connect the
cable to “
ANT.IN
” jack in rear panel of DVD-Video. Connect TV to DVD-Video. Connect “
RF OUT
” jack in DVD-
Video with “
ANT.IN
” jack in TV with RF cable.
Method
Method
2
2
: Connecting to a TV that has a audio/video in jacks
Connect
VIDEO OUT
jack in DVD-Video to
VIDEO IN
jack in TV, and
AUDIO OUT
jack in DVD-Video to
AUDIO
IN
jack in TV with connecting cable of Audio/Video jack. Select VCR mode by pressing TV/INPUT button in TV,
you can view more clear screen and sound than connection with RF cable only.
Method
Method
3
3
: Connecting to a TV that has a component video in jacks
Use a component video cable (commercially available) in place of the yellow video cable to enjoy higher quality
pictures. The component video connection only supplies video (picture) in the DVD mode of the DVD-Video.
Therefore, in order to use the VCR features or view TV channels at the DVD-Video, you still need to either
connect the RF coaxial cable between the ANT-OUT jack of the DVD-Video and the TV’s Antenna In jack, or
connect the video cable.
Method
Method
4
4
: Connecting to a TV that has a S-Video in jacks
Use a S-Video cable (not supplied) to enjoy higher quality pictures.
■
In the initial SET, exclusive channel for video is set to CH 3. To change this setting, set again in “CHANNEL
SET” screen in VCR operation.
■
In connecting RF cable to TV, set TV channel to CH3.
Connecting with TV
Connecting with Cable Box
How to connect
INPUT 1
IN
OUT
ANT IN
INPUT 2
R
ANT.IN
RF OUT
L
OUT
IN
AUDIO
VIDEO
OUT
OUT
IN
If your cable system only
requires you to use a converter
box for some channels
(i.e., pay-TV channels), follow
these steps: Find the primary
incoming RF cable. Plug this
cable into a splitter (available
at your local electronics store.)
■
You should install a distributor additionally.
How to watch general broadcasting with recording CATV
1
1
Set Channel Select switch of Converter Box to CH 3 or 4 as same as video exclusive channel. Press
[SET]
button in [VCR] operation to set video exclusive channel in “CHANNEL SET” screen.
2
2
Press channel button of Converter Box to select channel to be recorded. In this case, if you want to watch
CATV to be recorded, press [TV/INPUT] button of TV to select “Out (VCR)”.
3
3
Press
[REC]
button in DVD-Video.
4
4
To watch general broadcasting, press channel button in TV to select the desired channel.
Connect one RF cable between one OUT terminal on the splitter and the IN terminal on the converter box.
Connect another RF cable between the other OUT terminal on the splitter and the A-IN terminal on an A/B
switch (available at your local electronics store.) Connect a third RF cable between the OUT terminal on the
converter box and the B-IN terminal on the A/B switch.
Connect a RF cable between the OUT terminal on the A/B switch and the ANT. IN on your DVD-VIDEO.
When the A/B switch is in the B position, use the converter box to change channels ; when the A/B switch is in
the A position, use the DVD-VIDEO to change channels.
•
VHF
: 2 ~13 channels of TV ,
UHF
: 14~69 channels of TV,
CATV
: Broadcasting is transmitted with cable from
broadcasting station by contract with the station and consumers. It does not need any antenna.
• In/Out jack in Audio/Video terminal: - In: A jack used to receive signal required in this unit from other units. -
Out: A jack used to send signal of this unit to other units.
• Connect with Audio/Video terminal, you can enjoy more clear video and audio. (Use OUTPUT button in this remote
control to select video mode.)
• If screen is broken in connecting COMPONENT Out to Pr, Pb, Y of TV COMPONENT In jack , connect to Cr, Cb, Y.
• For some types of TV, you should press [TV/INPUT] button in TV remote control and convert from Out 1( VCR 1) or
Out 2(VCR 2) mode to Broadcasting Channel mode to change TV channel.
• Change channel selection of CATV receiver in recording, contents of recording is changed.
<Outside Antenna or Wall Antenna Outlet>
<Rear Panel of DVD-VIDEO>
<Rear Panel of TV>
Method 1
Method 2
<Rear Panel of DVD-VIDEO>
<Converter Box>
<Rear Panel of TV>
RF Cable
AUDIO/VIDEO Cable
RF Cable
RF Cable
<A/B Switch>
<Splitter (Not supported)>
<Cable Antenna>
RF Cable
Method 3
Method 4
